D-Link DES-3226 Reference Manual - Page 12

Introduction - des3226s

Get D-Link DES-3226 - Switch PDF manuals and user guides
UPC - 790069240560
View all D-Link DES-3226 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

DES-3226S Layer 2 Fast Ethernet Switch User's Guide the ports you assign to these VLANs and IP interfaces will be removed from the System interface. The IP address may be set using the Command Line Interface (CLI) over the console serial port as follows: 1. Starting at the command line prompt DES3226S:4# − enter the commands config ipif System ipaddress xxx.xxx.xxx.xxx/yyy.yyy.yyy.yyy. Where the x's represent the IP address to be assigned to the IP interface named System and the y's represent the corresponding subnet mask. 2. Alternaltively, you can enter DES3226S:4# − enter the commands config ipif System ipaddress xxx.xxx.xxx.xxx/z. Where the x's represent the IP address to be assigned to the IP interface named System and the z represents the corresponding number of subnets in CIDR notation. The IP interface named System on the switch can be assigned an IP address and subnet mask which can then be used to connect a management station to the switch's TELNET or web-based management agent. 12 Introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
DES-3226S Layer 2 Fast Ethernet Switch User’s Guide
12
Introduction
the ports you assign to these VLANs and IP interfaces will be
removed from the
System
interface.
The IP address may be set using the Command Line Interface (CLI)
over the console serial port as follows:
1.
Starting at the command line prompt
DES3226S:4#
−
enter the commands
config ipif System ipaddress
xxx.xxx.xxx.xxx/yyy.yyy.yyy.yyy
.
Where the
x
’s
represent the IP address to be assigned to the IP
interface named
System
and the
y
’s represent the
corresponding subnet mask.
2.
Alternaltively, you can enter
DES3226S:4#
−
enter the
commands
config
ipif
System
ipaddress
xxx.xxx.xxx.xxx/z
.
Where the
x
’s represent the IP
address to be assigned to the IP interface named
System
and the
z
represents the corresponding number
of subnets in CIDR notation.
The IP interface named
System
on the switch can be assigned an
IP address and subnet mask which can then be used to connect a
management station to the switch’s TELNET or web-based
management agent.