Dell Dimension 5150 Owner's Manual - Page 91

Installing a Floppy Drive

Get Dell Dimension 5150 PDF manuals and user guides View all Dell Dimension 5150 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Installing a Floppy Drive NOTE: In the event the replacement or new floppy drive does not have the shoulder screws, use the screws located within the drive panel insert. drive screws (4) 1 Follow the procedures in "Before You Begin" on page 59. 2 Remove the drive panel (see "Removing the Drive Panel" on page 80). 3 Gently slide the drive into place until you feel a click or feel the drive securely installed. NOTE: If you are installing a new floppy drive rather than replacing a drive, remove the drive panel insert where you want the drive to be installed, insert the shoulder screws located in the back of the drive panel insert into the drive, and then slide the drive back into place. 4 Attach the power and data cables to the floppy drive. 5 Connect the other end of the data cable to the connector labeled "DSKT2" on the system board (see "System Board Components" on page 67) and route the cable through the clip on the shroud. Removing and Installing Parts 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Removing and Installing Parts
91
Installing a Floppy Drive
NOTE:
In the event the replacement or new floppy drive does not have the shoulder screws, use the screws
located within the drive panel insert.
1
Follow the procedures in "Before You Begin" on page59.
2
Remove the drive panel (see "Removing the Drive Panel" on page 80).
3
Gently slide the drive into place until you feel a click or feel the drive securely installed.
NOTE:
If you are installing a new floppy drive rather than replacing a drive, remove the drive panel insert where
you want the drive to be installed, insert the shoulder screws located in the back of the drive panel insert into the
drive, and then slide the drive back into place.
4
Attach the power and data cables to the floppy drive.
5
Connect the other end of the data cable to the connector labeled "DSKT2" on the system board (see
"System Board Components" on page 67) and route the cable through the clip on the shroud.
drive
screws (4)