Home » Fujitsu Manuals » Hard Drives » Fujitsu MHN2150AT » Manual Viewer

Fujitsu MHN2150AT Manual/User Guide - Page 162

If A Device Configuration Set Command Has, Device Configuration Set Fr=c3h

Add to My Manuals
Save this manual to your list of manuals

Page 162 highlights

Interface If the device has executed a previous DEVICE CONFIGURATION FREEZE LOCK command since power-up, an aborted error is posted. • DEVICE CONFIGURATION IDENTIFY (FR=C2h) The DEVICE CONFIGURATION IDENTIFY command returns a 512 byte data structure is shown in Table 5.16. The content of this data structure indicates the selectable commands, modes, and feature sets that the device is capable of supporting. If a DEVICE CONFIGURATION SET command has been issued reducing the capabilities, the response to an IDENTIFY DEVICE command will reflect the reduced set of capabilities, while the DEVICE CONFIGURATION IDENTIFY command will reflect the entire set of selectable capabilities. If the device has executed a previous DEVICE CONFIGURATION FREEZE LOCK command since power-up, an aborted error is posted. • DEVICE CONFIGURATION SET (FR=C3h) The DEVICE CONFIGURATION SET command allows to reduce the set of optional commands, modes, or feature sets supported by a device as indicated by a DEVICE CONFIGURATION IDENTIFY command. The format of the overlay transmitted by the device is described in Table 5.16. The DEVICE CONFIGURATION SET command transfers an overlay that modifies some of the bits set in words 63, 82, 83, 84, and 88 of the IDENTIFY DEVICE command response. When the bits in these words are cleared, the device no longer supports the indicated command, mode, or feature set. If a bit is set in the overlay transmitted by the device that is not set in the overlay received from a DEVICE CONFIGURATION IDENTIFY command, no action is taken for that bit. After execution of this command, the settings are kept for the device power down or reset. If the restriction of Multiword DMA modes or Ultra DMA modes is executed, a SET FEATURES command should be issued for the modes restriction prior the DEVICE CONFIGURATION SET command is issued. If a DEVICE CONFIGURATION SET command has already modified the original settings as reported by a DEVICE CONFIGURATION IDENTIFY command, if DEVICE CONFIGURATION FREEZE LOCK is set, if any of the bit modification restrictions described are violated, or if a Host Protected Area has been established by the execution of a SET MAX ADDRESS command, an aborted error is posted. 5-86 C141-E120-02EN

Section	Page
Front Cover	1
FOR SAFE OPERATION	2
Revision History	3
Preface	5
Important Alert Items	9
Manual Organization	11
Contents	13
Figures	18
Tables	19
CHAPTER 1 Device Overview	21
1.1 Features	22
1.1.1 Functions and performance	22
1.1.2 Adaptability	22
1.1.3 Interface	23
1.2 Device Specifications	24
1.2.1 Specifications summary	24
1.2.2 Model and product number	25
1.3 Power Requirements	25
1.4 Environmental Specifications	27
1.5 Acoustic Noise	28
1.6 Shock and Vibration	28
1.7 Reliability	29
1.8 Error Rate	30
1.9 Media Defects	30
1.10Load/Unload Function	30
CHAPTER 2 Device Configuration	33
2.1 Device Configuration	34
2.2 System Configuration	36
2.2.1 ATA interface	36
2.2.2 1 drive connection	36
2.2.3 2 drives connection	36
CHAPTER 3 Installation Conditions	39
3.1 Dimensions	40
3.2 Mounting	41
3.3 Cable Connections	47
3.3.1 Device connector	47
3.3.2 Cable connector specifications	48
3.3.3 Device connection	48
3.3.4 Power supply connector (CN1)	49
3.4 Jumper Settings	49
3.4.1 Location of setting jumpers	49
3.4.2 Factory default setting	50
3.4.3 Master drive-slave drive setting	50
3.4.4 CSEL setting	51
CHAPTER 4 Theory of Device Operation	53
4.1 Outline	54
4.2 Subassemblies	54
4.2.1 Disk	54
4.2.2 Head	54
4.2.3 Spindle	55
4.2.4 Actuator	55
4.2.5 Air filter	55
4.3 Circuit Configuration	56
4.4 Power-on Sequence	59
4.5 Self-calibration	60
4.5.1 Self-calibration contents	60
4.5.2 Execution timing of self-calibration	61
4.5.3 Command processing during self-calibration	62
4.6 Read/write Circuit	62
4.6.1 Read/write preamplifier (HDIC)	62
4.6.2 Write circuit	62
4.6.3 Read circuit	65
4.6.4 Digital PLL circuit	66
4.7 Servo Control	67
4.7.1 Servo control circuit	67
4.7.2 Data-surface servo format	70
4.7.3 Servo frame format	72
4.7.4 Actuator motor control	73
4.7.5 Spindle motor control	74
CHAPTER 5 Interface	77
5.1 Physical Interface	78
5.1.1 Interface signals	78
5.1.2 Signal assignment on the connector	79
5.2 Logical Interface	82
5.2.1 I/O registers	83
5.2.2 Command block registers	84
5.2.3 Control block registers	89
5.3 Host Commands	89
5.3.1 Command code and parameters	90
5.3.2 Command descriptions	92
5.3.3 Error posting	164
5.4 Command Protocol	166
5.4.1 PIO Data transferring commands from device to host	166
5.4.2 PIO Data transferring commands from host to device	168
5.4.3 Commands without data transfer	170
5.4.4 Other commands	172
5.4.5 DMA data transfer commands	172
5.5 Ultra DMA Feature Set	175
5.5.1 Overview	175
5.5.2 Phases of operation	176
5.5.3 Ultra DMA data in commands	176
5.5.4 Ultra DMA data out commands	181
5.5.5 Ultra DMA CRC rules	185
5.5.6 Series termination required for Ultra DMA	186
5.6 Timing	187
5.6.1 PIO data transfer	187
5.6.2 Multiword data transfer	188
5.6.3 Ultra DMA data transfer	189
5.6.4 Power-on and reset	202
CHAPTER 6 Operations	203
6.1 Device Response to the Reset	204
6.1.1 Response to power-on	204
6.1.2 Response to hardware reset	205
6.1.3 Response to software reset	207
6.1.4 Response to diagnostic command	208
6.2 Power Save	209
6.2.1 Power save mode	209
6.2.2 Power commands	210
6.3 Defect Management	211
6.3.1 Spare area	211
6.3.2 Alternating defective sectors	211
6.4 Read-Ahead Cache	213
6.4.1 Data buffer configuration	214
6.4.2 Caching operation	214
6.4.3 Usage of read segment	216
6.5 Write Cache	222
Glossary	225
Acronyms and Abbreviations	229
Comment Form	231
Spine	233

Match case Limit results 1 per page

Interface

5-86

C141-E120-02EN

If the device has executed a previous DEVICE CONFIGURATION FREEZE

LOCK command since power-up, an aborted error is posted.

•

DEVICE CONFIGURATION IDENTIFY (FR=C2h)

The DEVICE CONFIGURATION IDENTIFY command returns a 512 byte

data structure is shown in Table 5.16.

The content of this data structure

indicates the selectable commands, modes, and feature sets that the device is

capable of supporting.

If a DEVICE CONFIGURATION SET command has

been issued reducing the capabilities, the response to an IDENTIFY DEVICE

command will reflect the reduced set of capabilities, while the DEVICE

CONFIGURATION IDENTIFY command will reflect the entire set of

selectable capabilities.

If the device has executed a previous DEVICE CONFIGURATION FREEZE

LOCK command since power-up, an aborted error is posted.

•

DEVICE CONFIGURATION SET (FR=C3h)

The DEVICE CONFIGURATION SET command allows to reduce the set of

optional commands, modes, or feature sets supported by a device as indicated

by a DEVICE CONFIGURATION IDENTIFY command.

The format of the

overlay transmitted by the device is described in Table 5.16.

The DEVICE

CONFIGURATION SET command transfers an overlay that modifies some

of the bits set in words 63, 82, 83, 84, and 88 of the IDENTIFY DEVICE

command response.

When the bits in these words are cleared, the device no

longer supports the indicated command, mode, or feature set.

If a bit is set in

the overlay transmitted by the device that is not set in the overlay received

from a DEVICE CONFIGURATION IDENTIFY command, no action is

taken for that bit.

After execution of this command, the settings are kept for

the device power down or reset.

If the restriction of Multiword DMA modes or Ultra DMA modes is

executed, a SET FEATURES command should be issued for the modes

restriction prior the DEVICE CONFIGURATION SET command is issued.

If a DEVICE CONFIGURATION SET command has already modified the

original settings as reported by a DEVICE CONFIGURATION IDENTIFY

command, if DEVICE CONFIGURATION FREEZE LOCK is set, if any of

the bit modification restrictions described are violated, or if a Host Protected

Area has been established by the execution of a SET MAX ADDRESS

command, an aborted error is posted.