Garmin GTR 200 GTR 200 Installation Manual - Page 39

Lighting Bus Interface Check, Discrete Input Checkout, Table 3-10, Discrete Inputs - disc wire

Get Garmin GTR 200 PDF manuals and user guides View all Garmin GTR 200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

3.6.5.4 Lighting Bus Interface Check The display and bezel key backlighting on the GTR 200 can track an external lighting/dimmer bus input and use it to vary the display and bezel key backlight levels accordingly. This check is only applicable if Lighting Source (on the Lighting Setup Page, Section 3.6.4.6) is set to 14V or 28V, and verifies that the interface is connected correctly. 1. Refer to Section 3.6.4 to select the Lighting Setup Page. 2. Ensure the lighting bus input is set to its minimum setting. 3. Slowly vary the input lighting bus level. Verify that the display brightness tracks the lighting bus setting. Continue to maximum brightness and verify proper operation. 3.6.5.5 Discrete Input Checkout If one or both discrete inputs (Table 3-10) are connected, the wiring is checked using the following procedure. 1. Refer to Section 3.6.4 to select the Discrete Setup Page (Section 3.6.4.5). 2. While the momentary contact pushbutton(s) are not being pressed (inputs are not grounded), verify the DISC 1 and DISC 2 check boxes are not checked. If one or both boxes is checked, the wiring is likely the cause of the failure. 3. Activate the DISC 1 and/or DISC 2 input by pressing the associated momentary contact pushbutton (inputs are grounded). Verify the appropriate checkbox is checked. If the checkbox is not checked the wiring is likely the cause of the failure. Table 3-10 Discrete Inputs Pin Pin Name 2 DISC 1 22 DISC 2 Description Configurable discrete active low input 1 Configurable discrete active low input 2 190-01553-00 Rev. A GTR 200 Installation Manual Page 3-17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
190-01553-00
GTR 200 Installation Manual
Rev. A
Page 3-17
3.6.5.4
Lighting Bus Interface Check
The display and bezel key backlighting on the GTR 200 can track an external lighting/dimmer bus input
and use it to vary the display and bezel key backlight levels accordingly. This check is only applicable if
Lighting Source (on the Lighting Setup Page,
Section 3.6.4.6
) is set to 14V or 28V, and verifies that the
interface is connected correctly.
1.
Refer to
Section 3.6.4
to select the Lighting Setup Page.
2.
Ensure the lighting bus input is set to its minimum setting.
3.
Slowly vary the input lighting bus level.
Verify that the display brightness tracks the lighting bus
setting.
Continue to maximum brightness and verify proper operation.
3.6.5.5
Discrete Input Checkout
If one or both discrete inputs (Table 3-10) are connected, the wiring is checked using the following
procedure.
1.
Refer to
Section 3.6.4
to select the Discrete Setup Page (
Section 3.6.4.5)
.
2.
While the momentary contact pushbutton(s) are not being pressed (inputs are not grounded), verify
the DISC 1 and DISC 2 check boxes are not checked.
If one or both boxes is checked, the wiring
is likely the cause of the failure.
3.
Activate the DISC 1 and/or
DISC 2 input by pressing the associated momentary contact
pushbutton (inputs are grounded).
Verify the appropriate checkbox is checked.
If the checkbox is
not checked the wiring is likely the cause of the failure.
Table 3-10
Discrete Inputs
Pin
Pin Name
Description
2
DISC 1
Configurable discrete active low input 1
22
DISC 2
Configurable discrete active low input 2