Garmin GTR 200 GTR 200 Installation Manual - Page 60

A.6 Daisy Chain between Methods A and B, A.7 Splicing Signal Wires, A-7

Get Garmin GTR 200 PDF manuals and user guides View all Garmin GTR 200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

A.6 Daisy Chain between Methods A and B In rare situations where more braids need to be terminated for a connector than three per ring terminal and a mixture of Methods A and B have been used, it is allowable to daisy chain a maximum of two shields together from a Method A termination to a Method B (Figure A-7). All other restrictions and instructions for the shield termination technique set forth for Method A and B are still applicable. NOTE The maximum length of the combined braids should be approximately 4 inches. Figure A-7 Daisy Chain between Methods A and B A.7 Splicing Signal Wires NOTE Figure A-8 illustrates that a splice must be made within a 3 inch window from outside the edge of clamp to the end of the 3 inch max mark. WARNING Keep the splice out of the backshell for pin extraction, and outside of the strain relief to avoid preloading. Figure A-8 shows a two wire splice, but a maximum of three wires can be spliced. If a third wire is spliced, it is located out front of splice along with signal wire going to pin. Splice part numbers: •Raychem D-436-36/37/38 •MIL Spec MIL-S-81824/1 This technique may be used with shield termination methods: A.1, A.2, B.1, and B.2. GTR 200 Installation Manual Page A-10 190-01553-00 Rev. A

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
GTR 200 Installation Manual
190-01553-00
Page A-10
Rev. A
A.6
Daisy Chain between Methods A and B
In rare situations where more braids need to be terminated for a connector than three per ring terminal and
a mixture of Methods A and B have been used, it is allowable to daisy chain a maximum of two shields
together from a Method A termination to a Method B (Figure A-7).
All other restrictions and instructions
for the shield termination technique set forth for Method A and B are still applicable.
NOTE
The maximum length of the combined braids should be approximately 4 inches.
Figure A-7
Daisy Chain between Methods A and B
A.7
Splicing Signal Wires
NOTE
Figure A-8
illustrates that a splice must be made within a 3 inch window from outside the
edge of clamp to the end of the 3 inch max mark.
WARNING
Keep the splice out of the backshell for pin extraction, and outside of the strain relief to
avoid preloading.
Figure A-8 shows a two wire splice, but a maximum of three wires can be spliced.
If a third wire is
spliced, it is located out front of splice along with signal wire going to pin.
Splice part numbers:
•Raychem D-436-36/37/38
•MIL Spec MIL-S-81824/1
This technique may be used with shield termination methods: A.1, A.2, B.1, and B.2.