Garmin GTR 200 GTR 200 Installation Manual - Page 51

Appendix A Shield Block Connector Installation Instructions, A.1 Shield Block Installation Parts - specs

Get Garmin GTR 200 PDF manuals and user guides View all Garmin GTR 200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

APPENDIX A SHIELD BLOCK CONNECTOR INSTALLATION INSTRUCTIONS A.1 Shield Block Installation Parts Table 2-3 and Table A-1 list the parts needed to install a Shield Block. Parts listed in Table 2-3 are supplied in the GTR 200 Connector Kit (011-003240-00). Parts listed in Table A-1 are to be provided by the installer. Table A-1 Parts not supplied for a Shield Block Installation (Figure A-1) Figure Ref 4 5 6 7 13 Description GPN or MIL spec Multiple Conductor Shielded Cable (2-conductor shown in Figure A-1) Drain Wire Shield Termination (method optional) Braid, Flat (19-20 AWG equivalent, tinned plated copper strands 36 AWG, Circular Mil Area 1000 -1300) Floating Shield Termination (method optional) Silicon Fusion Tape Parts used depend on method chosen Parts used depend on method chosen Parts used depend on method chosen Parts used depend on method chosen - NOTE In Figure A-1, "AR" denotes quantity "As Required" for the particular installation. 190-01553-00 Rev. A GTR 200 Installation Manual Page A-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
190-01553-00
GTR 200 Installation Manual
Rev. A
Page A-1
APPENDIX A
SHIELD BLOCK CONNECTOR INSTALLATION
INSTRUCTIONS
A.1
Shield Block Installation Parts
Table 2-3
and Table A-1 list the parts needed to install a Shield Block.
Parts listed in
Table 2-3
are
supplied in the GTR 200 Connector Kit (011-003240-00).
Parts listed in Table A-1 are to be provided by
the installer.
NOTE
In Figure A-1, “AR” denotes quantity “As Required” for the particular installation.
Table A-1
Parts not supplied for a Shield Block Installation (Figure A-1)
Figure
Ref
Description
GPN or MIL spec
4
Multiple Conductor Shielded Cable (2-conductor shown in
Figure A-1
)
Parts used depend on
method chosen
5
Drain Wire Shield Termination (method optional)
Parts used depend on
method chosen
6
Braid, Flat (19-20 AWG equivalent, tinned plated copper strands
36 AWG, Circular Mil Area 1000 -1300)
Parts used depend on
method chosen
7
Floating Shield Termination (method optional)
Parts used depend on
method chosen
13
Silicon Fusion Tape
-