HP DL560 HP ProLiant DL560 Server User Guide - Page 108

SmartStart Cannot Load Operating System, ROMPaq Disaster Recovery

Get HP DL560 - ProLiant - 1 GB RAM PDF manuals and user guides
UPC - 808736876919
View all HP DL560 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

108 HP ProLiant DL560 Server User Guide SmartStart Cannot Load Operating System Possible Cause Required operating system step was missed. Installation problem occurred. Problem was encountered with the hardware you have added to the system. Problem was encountered with hardware added to a new configure-to-order system (where available). Possible Solution Follow these steps: 1. Note at which phase the operating system failed. 2. Remove any loaded operating system. 3. Refer to the operating system documentation. 4. Install the operating system again. Refer to the operating system documentation and to the SmartStart Release Notes on the SmartStart CD. Run RBSU and check the OS Selection menu. Refer to the documentation provided with the hardware. You must complete the factory-installed operating system software installation before adding new hardware to the system. Be sure you are following the instructions provided in the HP Factory-Installed Operating System Software Installation Guide. Remove the new hardware and complete the software installation. Then, reinstall the new hardware. ROMPaq Disaster Recovery If both the current and backup versions of the ROM are corrupt, perform ROMPaq disaster recovery procedures: 1. Create a ROMPaq diskette using the Autorun Menu on the SmartStart CD. 2. Power down the server ("Powering Down the Server" on page 29).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
108
HP ProLiant DL560 Server User Guide
SmartStart Cannot Load Operating System
Possible Cause
Possible Solution
Required operating system
step was missed.
Follow these steps:
1.
Note at which phase the operating system
failed.
2. Remove any loaded operating system.
3. Refer to the operating system
documentation.
4. Install the operating system again.
Installation problem
occurred.
Refer to the operating system documentation
and to the SmartStart Release Notes on the
SmartStart CD.
Run RBSU and check the
OS Selection
menu.
Problem was encountered
with the hardware you have
added to the system.
Refer to the documentation provided with the
hardware.
Problem was encountered
with hardware added to a
new configure-to-order
system (where available).
You must complete the factory-installed
operating system software installation before
adding new hardware to the system.
Be sure you are following the instructions
provided in the
HP Factory-Installed Operating
System Software Installation Guide
.
Remove the new hardware and complete the
software installation. Then, reinstall the new
hardware.
ROMPaq Disaster Recovery
If both the current and backup versions of the ROM are corrupt, perform
ROMPaq disaster recovery procedures:
1.
Create a ROMPaq diskette using the Autorun Menu on the SmartStart CD.
2.
Power down the server ("Powering Down the Server" on page 29).