HP DL560 HP ProLiant DL560 Server User Guide - Page 85

Boot Options, HP ROM-Based Setup Utility Guide

Get HP DL560 - ProLiant - 1 GB RAM PDF manuals and user guides
UPC - 808736876919
View all HP DL560 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Server Configuration and Utilities 85 NOTE: The server may not support all of the following examples. Drives Installed Drives Used RAID Level 1 1 RAID 0 2 2 RAID 1 3, 4, 5, or 6 3, 4, 5, or 6 RAID 5 More than 6 0 None NOTE: If the boot drive is not empty or has been written to in the past, ORCA does not automatically configure the array. You must run ORCA to configure the array settings. To change any ORCA default settings and override the auto-configuration process, press the F8 key when prompted. By default, the auto-configuration process configures the system for a Microsoft Windows 2000 operating system and the English language. To change any default settings in the auto-configuration process, such as the settings for language, operating system, and primary boot controller, execute RBSU by pressing the F9 key when prompted. After the settings are selected, exit RBSU and allow the server to reboot automatically. For more information, refer to the HP ROM-Based Setup Utility Guide on the Documentation CD or the white paper on the HP website (ftp://ftp.compaq.com/pub/products/servers/management/rbsu-whitepaper.pdf). Boot Options After the auto-configuration process completes, or after the server reboots upon exit from RBSU, the POST sequence runs, and then the boot option screen is displayed. This screen is visible for several seconds before the system attempts to boot from either a diskette, CD, or hard drive. During this time, the menu on the screen allows you to install an operating system or make changes to the server configuration in RBSU.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
Server Configuration and Utilities
85
NOTE:
The server may not support all of the following examples.
Drives Installed
Drives Used
RAID Level
1
1
RAID 0
2
2
RAID 1
3, 4, 5, or 6
3, 4, 5, or 6
RAID 5
More than 6
0
None
NOTE:
If the boot drive is not empty or has been written to in
the past, ORCA does not automatically configure the array. You
must run ORCA to configure the array settings.
To change any ORCA default settings and override the auto-configuration
process, press the
F8
key when prompted.
By default, the auto-configuration process configures the system for a Microsoft
Windows 2000 operating system and the English language. To change any
default settings in the auto-configuration process, such as the settings for
language, operating system, and primary boot controller, execute RBSU by
pressing the
F9
key when prompted. After the settings are selected, exit RBSU
and allow the server to reboot automatically.
For more information, refer to the
HP ROM-Based Setup Utility Guide
on the
Documentation CD or the white paper on the HP website
(
).
Boot Options
After the auto-configuration process completes, or after the server reboots upon
exit from RBSU, the POST sequence runs, and then the boot option screen is
displayed. This screen is visible for several seconds before the system attempts to
boot from either a diskette, CD, or hard drive. During this time, the menu on the
screen allows you to install an operating system or make changes to the server
configuration in RBSU.