HP DL560 HP ProLiant DL560 Server User Guide - Page 88

SmartStart Software, Administer User Accounts, Con iLO Settings, Network, DNS/DHCP, Enter

Get HP DL560 - ProLiant - 1 GB RAM PDF manuals and user guides
UPC - 808736876919
View all HP DL560 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

88 HP ProLiant DL560 Server User Guide 2. Press the F8 key when prompted during POST. The iLO RBSU runs. 3. Enter a valid iLO user ID and password with the appropriate iLO privileges (Administer User Accounts, Configure iLO Settings). Default account information is located on the iLO Default Network Settings tag. 4. Make and save any necessary changes to the iLO configuration. 5. Exit iLO RBSU. HP recommends using DNS/DHCP with iLO to simplify installation. If DNS/DHCP cannot be used, use the following procedure to disable DNS/DHCP and to configure the IP address and the subnet mask: 1. Restart or power up the server. 2. Press the F8 key when prompted during POST. The iLO RBSU runs. 3. Enter a valid iLO user ID and password with the appropriate iLO privileges (Administer User Accounts, Configure iLO Settings). Default account information is located on the iLO Default Network Settings tag. 4. Select Network, DNS/DHCP, press the Enter key, and then select DHCP Enable. Press the spacebar to turn off DHCP. Be sure that DHCP Enable is set to Off and save the changes. 5. Select Network, NIC and TCP/IP, press the Enter key, and type the appropriate information in the IP Address, Subnet Mask and Gateway IP Address fields. 6. Save the changes. The iLO system automatically resets to use the new setup when you exit iLO RBSU. SmartStart Software SmartStart software is a CD-based, single-server method for installing system software, thereby achieving a well-integrated server and ensuring maximum dependability and supportability. The SmartStart CD contains tools that diagnose problems with the server, configure storage arrays, and update the system ROM. SmartStart software enables you to: • Install selected server operating systems using packaged product CDs.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
88
HP ProLiant DL560 Server User Guide
2. Press the
F8
key when prompted during POST. The iLO RBSU runs.
3.
Enter a valid iLO user ID and password with the appropriate iLO privileges
(
Administer User Accounts
,
Configure iLO Settings
). Default account
information is located on the iLO Default Network Settings tag.
4.
Make and save any necessary changes to the iLO configuration.
5. Exit iLO RBSU.
HP recommends using DNS/DHCP with iLO to simplify installation. If
DNS/DHCP cannot be used, use the following procedure to disable DNS/DHCP
and to configure the IP address and the subnet mask:
1.
Restart or power up the server.
2. Press the
F8
key when prompted during POST. The iLO RBSU runs.
3.
Enter a valid iLO user ID and password with the appropriate iLO privileges
(
Administer User Accounts
,
Configure iLO Settings
). Default account
information is located on the iLO Default Network Settings tag.
4. Select
Network
,
DNS/DHCP
, press the
Enter
key, and then select
DHCP
Enable
. Press the spacebar to turn off DHCP. Be sure that
DHCP Enable
is
set to
Off
and save the changes.
5. Select
Network
,
NIC and TCP/IP
, press the
Enter
key, and type the
appropriate information in the
IP Address
,
Subnet Mask
and
Gateway IP
Address
fields.
6.
Save the changes. The iLO system automatically resets to use the new setup
when you exit iLO RBSU.
SmartStart Software
SmartStart software is a CD-based, single-server method for installing system
software, thereby achieving a well-integrated server and ensuring maximum
dependability and supportability. The SmartStart CD contains tools that diagnose
problems with the server, configure storage arrays, and update the system ROM.
SmartStart software enables you to:
•
Install selected server operating systems using packaged product CDs.