HP Engage Go 13.5 Maintenance and Service Guide - Page 19

Attaching an I/O connectivity base to the mobile system

Get HP Engage Go 13.5 PDF manuals and user guides View all HP Engage Go 13.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

■ Press the lock release button (1) on the front of the dock's column, and then lift the mobile head unit (2) off the dock. Attaching an I/O connectivity base to the mobile system You can attach an I/O connectivity base to the bottom of the stand. To attach an I/O connectivity base: 1. Turn off the mobile system properly through the operating system, and turn off any external devices. 2. Disconnect the power cords from the mobile system and I/O connectivity base. IMPORTANT: Regardless of the power state, voltage is always present on the system board as long as the system is plugged into an active AC outlet. You must disconnect the power cord and wait approximately 30 seconds for the power to drain to avoid damage to the internal components. 3. Remove the cover from the I/O connectivity base by removing the four screws on the underside of the I/O connectivity base (1) and then lifting the cover off the I/O connectivity base (2). 12 Chapter 2 Hardware setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
■
Press the lock release button
(1)
on the front of the dock’s column, and then lift the mobile head unit
(2)
off the dock.
Attaching an I/O connectivity base to the mobile system
You can attach an I/O connectivity base to the bottom of the stand.
To attach an I/O connectivity base:
1.
Turn off the mobile system properly through the operating system, and turn off any external
devices.
2.
Disconnect the power cords from the mobile system and I/O connectivity base.
IMPORTANT:
Regardless of the power state, voltage is always present on the system board as
long as the system is plugged into an active AC outlet. You must disconnect the power cord and
wait approximately 30 seconds for the power to drain to avoid damage to the internal components.
3.
Remove the cover from the I/O connectivity base by removing the four screws on the underside of
the I/O connectivity base
(1)
and then lifting the cover off the I/O connectivity base
(2)
.
12
Chapter 2
Hardware setup