HP Engage Go 13.5 Maintenance and Service Guide - Page 52

Power button board

Get HP Engage Go 13.5 PDF manuals and user guides View all HP Engage Go 13.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

1. Disconnect the cable from the reverse ZIF connector on the system board (1). 2. Remove the two Phillips screws (2) from the connector. 3. Pull the pogo connector into the computer slightly, and then remove it from the computer (3). 4. If you need to remove the pogo docking connectors, remove the Phillips screw (1) from each holder, and then remove the holders from the computer (2). To install the pogo connector and docking connectors, reverse the removal procedures. Power button board To remove the power button board, use this procedure and illustration. Before removing the power button board, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 31). 2. Remove the display assembly (see Display assembly on page 31). Power button board 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
1.
Disconnect the cable from the reverse ZIF connector on the system board
(1)
.
2.
Remove the two Phillips screws
(2)
from the connector.
3.
Pull the pogo connector into the computer slightly, and then remove it from the computer
(3)
.
4.
If you need to remove the pogo docking connectors, remove the Phillips screw
(1)
from each holder,
and then remove the holders from the computer
(2)
.
To install the pogo connector and docking connectors, reverse the removal procedures.
Power button board
To remove the power button board, use this procedure and illustration.
Before removing the power button board, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
31
).
2.
Remove the display assembly (see
Display assembly
on page
31
).
Power button board
45