HP Engage Go 13.5 Maintenance and Service Guide - Page 21

Connecting a standalone I/O connectivity base to the mobile system

Get HP Engage Go 13.5 PDF manuals and user guides View all HP Engage Go 13.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

6. To connect and secure the USB Type-C power cable, attach the cable clip to the cable (1), insert the cable tie into the hole (2) below the USB Type-C port on the I/O connectivity base, and then slide the cable clip onto the cable tie and connect the cable to the port (3). 7. Connect the AC adapter to the I/O connectivity base and a grounded AC outlet. See Connecting an AC adapter to power on page 7. Connecting a standalone I/O connectivity base to the mobile system You can connect a standalone I/O connectivity base to the mobile system. To connect a standalone I/O connectivity base: 1. Turn off the mobile system properly through the operating system, and turn off any external devices. 2. Disconnect the power cords from the mobile system and I/O connectivity base. IMPORTANT: Regardless of the power state, voltage is always present on the system board as long as the system is plugged into an active AC outlet. You must disconnect the power cord and wait approximately 30 seconds for the power to drain to avoid damage to the internal components. 3. Connect the USB Type-C power cable to the USB Type-C port on the underside of the stand's column and to the USB Type-C power port on the I/O connectivity base. 14 Chapter 2 Hardware setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
6.
To connect and secure the USB Type-C power cable, attach the cable clip to the cable
(1)
, insert the
cable tie into the hole
(2)
below the USB Type-C port on the I/O connectivity base, and then slide the
cable clip onto the cable tie and connect the cable to the port
(3)
.
7.
Connect the AC adapter to the I/O connectivity base and a grounded AC outlet. See
Connecting an
AC adapter to power
on page
7
.
Connecting a standalone I/O connectivity base to the mobile
system
You can connect a standalone I/O connectivity base to the mobile system.
To connect a standalone I/O connectivity base:
1.
Turn off the mobile system properly through the operating system, and turn off any external
devices.
2.
Disconnect the power cords from the mobile system and I/O connectivity base.
IMPORTANT:
Regardless of the power state, voltage is always present on the system board as
long as the system is plugged into an active AC outlet. You must disconnect the power cord and
wait approximately 30 seconds for the power to drain to avoid damage to the internal components.
3.
Connect the USB Type-C power cable to the USB Type-C port on the underside of the stand’s
column and to the USB Type-C power port on the I/O connectivity base.
14
Chapter 2
Hardware setup