HP Engage Go 13.5 Maintenance and Service Guide - Page 42

Hub board, Disconnect the cable from the ZIF connector on the left side of the board

Get HP Engage Go 13.5 PDF manuals and user guides View all HP Engage Go 13.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

■ Use a flat tool (1) to release the board out from the computer (2). The board is secured with adhesive. To install the touch board, reverse the removal procedure. Hub board To remove the hub board, use this procedure and illustration. Before removing the hub board, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 31). 2. Remove the display assembly (see Display assembly on page 31). 3. Disconnect the battery cable from the system board (see Battery on page 32). Remove the hub board: 1. Disconnect the cable from the ZIF connector on the left side of the board (1). 2. Disconnect the cable from the reverse ZIF connector on the right side of the board (2). 3. Disconnect the lower cable, located under the top cable, on the right side of the board (3). 4. Remove the two Phillips screws from the board (4). Hub board 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
■
Use a flat tool
(1)
to release the board out from the computer
(2)
. The board is secured with adhesive.
To install the touch board, reverse the removal procedure.
Hub board
To remove the hub board, use this procedure and illustration.
Before removing the hub board, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
31
).
2.
Remove the display assembly (see
Display assembly
on page
31
).
3.
Disconnect the battery cable from the system board (see
Battery
on page
32
).
Remove the hub board:
1.
Disconnect the cable from the ZIF connector on the left side of the board
(1)
.
2.
Disconnect the cable from the reverse ZIF connector on the right side of the board
(2)
.
3.
Disconnect the lower cable, located under the top cable, on the right side of the board
(3)
.
4.
Remove the two Phillips screws from the board
(4)
.
Hub board
35