HP Pavilion m7-1000 HP Pavilion dv7 Entertainment PC - Maintenance and Service - Page 78

USB board

Get HP Pavilion m7-1000 PDF manuals and user guides View all HP Pavilion m7-1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Remove the solid-state drive: 1. Remove the Phillips PM2.0×3.0 screw (1) that secures the solid-state drive to the system board. (The solid-state drive tilts up.) 2. Remove the solid-state drive by pulling the drive away from the slot at an angle (2). NOTE: The solid-state drive is designed with a notch to prevent incorrect installation into the solid-state drive slot. Reverse this procedure to install the solid-state drive. USB board Description USB board (includes cable) Spare part number 681986-001 Before removing the USB board, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 45), and then remove the following components: a. Hard drive (see Hard drive on page 46) b. Optical drive (see Optical drive on page 51) 70 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Remove the solid-state drive:
1.
Remove the Phillips PM2.0×3.0 screw
(1)
that secures the solid-state drive to the system board.
(The solid-state drive tilts up.)
2.
Remove the solid-state drive by pulling the drive away from the slot at an angle
(2)
.
NOTE:
The solid-state drive is designed with a notch to prevent incorrect installation into
the solid-state drive slot.
Reverse this procedure to install the solid-state drive.
USB board
Description
Spare part number
USB board (includes cable)
681986-001
Before removing the USB board, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
45
), and then remove the following components:
a.
Hard drive (see
Hard drive
on page
46
)
b.
Optical drive (see
Optical drive
on page
51
)
70
Chapter 4
Removal and replacement procedures