HP Photosmart C6100 Basics Guide - Page 85

Fax Line Condition Test, Cause, Solution, HP Photosmart C6100 All-in-One series, Latin America - power cord

Page 85 highlights

Troubleshooting and support Chapter 5 ● Other equipment, which uses the same phone line as the HP All-in-One, might be causing the test to fail. To find out if other equipment is causing a problem, disconnect everything except the HP All-in-One from the phone line, and then run the test again. - If the Fax Line Condition Test passes without the other equipment, then one or more pieces of the equipment is causing problems; try adding them back one at a time and rerunning the test each time, until you identify which piece of equipment is causing the problem. - If the Fax Line Condition Test fails without the other equipment, connect the HP Allin-One to a working phone line and continue reviewing the troubleshooting information in this section. ● If you are using a phone splitter, this can cause faxing problems. (A splitter is a two-cord connector that plugs into a telephone wall jack.) Try removing the splitter and connecting the HP All-in-One directly to the telephone wall jack. After you resolve any problems found, run the fax test again to make sure it passes and the HP All-in-One is ready for faxing. If the Fax Line Condition test continues to fail and you experience problems faxing, contact your telephone company and have them check the phone line. The HP All-in-One is having problems sending and receiving faxes Cause The HP All-in-One is not set up properly for faxing. Solution Follow the instructions in this guide to set up the HP All-in-One properly for faxing, based on the equipment and services you have on the same phone line as the HP All-in-One. Then, run a fax test to check the status of the HP All-in-One and to make sure you set it up properly. The HP All-in-One prints a report with the results of the test. If the test fails, review the report for information on how to fix the problem. Cause The HP All-in-One is turned off. Solution Look at the display on the HP All-in-One. If the display is blank and the On button is not lit, the HP All-in-One is turned off. Make sure the power cord is firmly connected to the HP All-in-One and plugged into a power outlet. Press the On button to turn on the HP All-inOne. Cause The wrong phone cord is used to connect the HP All-in-One or the phone cord is plugged into the wrong port. Solution Note This possible solution applies only in the countries/regions that receive a 2-wire phone cord in the box with the HP All-in-One, including: Argentina, Australia, Brazil, Canada, Chile, China, Colombia, Greece, India, Indonesia, Ireland, Japan, Korea, Latin America, Malaysia, Mexico, Philippines, Poland, Portugal, Russia, Saudi Arabia, Singapore, Spain, Taiwan, Thailand, USA, Venezuela, and Vietnam. Make sure you used the phone cord supplied in the box with the HP All-in-One to connect to the telephone wall jack. One end of this special 2-wire phone cord should be connected to the 82 HP Photosmart C6100 All-in-One series

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118

Other equipment, which uses the same phone line as the HP All-in-One, might be causing
the test to fail. To find out if other equipment is causing a problem, disconnect everything
except the HP All-in-One from the phone line, and then run the test again.
If the
Fax Line Condition Test
passes without the other equipment, then one or
more pieces of the equipment is causing problems; try adding them back one at a
time and rerunning the test each time, until you identify which piece of equipment is
causing the problem.
If the
Fax Line Condition Test
fails without the other equipment, connect the HP All-
in-One to a working phone line and continue reviewing the troubleshooting
information in this section.
If you are using a phone splitter, this can cause faxing problems. (A splitter is a two-cord
connector that plugs into a telephone wall jack.) Try removing the splitter and connecting
the HP All-in-One directly to the telephone wall jack.
After you resolve any problems found, run the fax test again to make sure it passes and the
HP All-in-One is ready for faxing. If the
Fax Line Condition
test continues to fail and you
experience problems faxing, contact your telephone company and have them check the phone
line.
The HP All-in-One is having problems sending and receiving faxes
Cause
The HP All-in-One is not set up properly for faxing.
Solution
Follow the instructions in this guide to set up the HP All-in-One properly for faxing,
based on the equipment and services you have on the same phone line as the HP All-in-One.
Then, run a fax test to check the status of the HP All-in-One and to make sure you set it up
properly.
The HP All-in-One prints a report with the results of the test. If the test fails, review the report
for information on how to fix the problem.
Cause
The HP All-in-One is turned off.
Solution
Look at the display on the HP All-in-One. If the display is blank and the
On
button
is not lit, the HP All-in-One is turned off. Make sure the power cord is firmly connected to the
HP All-in-One and plugged into a power outlet. Press the
On
button to turn on the HP All-in-
One.
Cause
The wrong phone cord is used to connect the HP All-in-One or the phone cord is
plugged into the wrong port.
Solution
Note
This possible solution applies only in the countries/regions that receive a 2-wire
phone cord in the box with the HP All-in-One, including: Argentina, Australia, Brazil,
Canada, Chile, China, Colombia, Greece, India, Indonesia, Ireland, Japan, Korea,
Latin America, Malaysia, Mexico, Philippines, Poland, Portugal, Russia, Saudi Arabia,
Singapore, Spain, Taiwan, Thailand, USA, Venezuela, and Vietnam.
Make sure you used the phone cord supplied in the box with the HP All-in-One to connect to
the telephone wall jack. One end of this special 2-wire phone cord should be connected to the
Chapter 5
82
HP Photosmart C6100 All-in-One series
Troubleshooting and support