HP RP3 Maintenance & Service Guide HP RP3 Retail System Model 3100 - Page 39

Hard Drive

Get HP RP3 PDF manuals and user guides View all HP RP3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Hard Drive NOTE: The HP RP3 computer supports 2.5-inch Serial ATA (SATA) internal hard drives. Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. The 2.5-inch hard drive is enclosed in a carrier on the interior of the front panel. To replace the drive: 1. Prepare the computer for disassembly (Preparation for Disassembly on page 15). 2. Remove the access panel (Access Panel on page 16). 3. Disconnect the cables from the rear of the hard drive. 4. Press outward on the release latch located on the front panel just above the cable connection on the hard drive (1), then slide the carrier toward the center of the chassis and pull the carrier straight back from the front panel to remove it (2). 32 Chapter 4 Removal and Replacement Procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Hard Drive
NOTE:
The HP RP3 computer supports 2.5-inch Serial ATA (SATA) internal hard drives.
Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you
can transfer the data to the new hard drive.
The 2.5-inch hard drive is enclosed in a carrier on the interior of the front panel. To replace the drive:
1.
Prepare the computer for disassembly (
Preparation for Disassembly
on page
15
).
2.
Remove the access panel (
Access Panel
on page
16
).
3.
Disconnect the cables from the rear of the hard drive.
4.
Press outward on the release latch located on the front panel just above the cable connection on
the hard drive
(1)
, then slide the carrier toward the center of the chassis and pull the carrier
straight back from the front panel to remove it
(2)
.
32
Chapter 4
Removal and Replacement Procedures