Honeywell MS9535-5 User Manual - Page 12

Keyboard Wedge, Cradle Installation To The Host Device - battery

Get Honeywell MS9535-5 PDF manuals and user guides View all Honeywell MS9535-5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

CRADLE INSTALLATION TO THE HOST DEVICE Keyboard Wedge 1. Turn off the host device. 2. Connect the 10-pin RJ45 male connector into the 10-pin modular jack on the bottom of the cradle. 3. Disconnect the keyboard from host. 4. Connect the "Y" ends of the communication cable to the keyboard and keyboard port on the host device. If necessary, use the male/female adapter cable supplied with the scanner for the proper connections. 5. Plug the external power supply into the power jack on the bottom of the cradle. Check the AC input requirements of the power supply to make sure the voltage matches the AC outlet. The outlet must be located near the requirement and be easily accessible. Figure 5. Keyboard Wedge 6. Plug the power supply into the AC outlet. The blue LED on the rear of the cradle will stay on. 7. Turn on the host device. 8. Establish communication between the scanner and cradle. See page 15 for complete instructions on Establishing Bluetooth Communication between the scanner and cradle. The scanner must be charged for a minimum of 3 hours before the scanner can be placed in full operation for the first time. After the initial preparation charge of 3 hrs, the battery will only require 2.5 hrs to come to a full charge when it gives a Low Power warning (see page 18). See page 6. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
8
C
RADLE
I
NSTALLATION TO THE
H
OST
D
EVICE
Keyboard Wedge
1.
Turn off the host device.
2.
Connect the 10-pin RJ45 male
connector into the 10-pin modular
jack on the bottom of the cradle.
3.
Disconnect the keyboard from host.
4.
Connect the “Y” ends of the
communication cable to the
keyboard and keyboard port on the
host device.
If necessary, use the
male/female adapter cable supplied
with the scanner for the proper
connections.
5.
Plug the external power supply into
the power jack on the bottom of the
cradle.
Check the AC input
requirements of the power
supply to make sure the
voltage matches the AC
outlet. The outlet must be
located near the
requirement and be easily
accessible.
6.
Plug the power supply into the AC outlet.
The blue LED on the rear of the
cradle will stay on.
7.
Turn on the host device.
8.
Establish communication between the scanner and cradle.
See page 15 for complete instructions on
Establishing Bluetooth
Communication
between the scanner and cradle.
The scanner must be charged for a minimum of 3 hours before the
scanner
can be placed in full operation for the first time.
After the initial
preparation
charge of 3 hrs, the battery will only require 2.5 hrs to come
to a full charge when it gives a Low Power
warning (
see page 18)
.
See page 6.
Figure 5. Keyboard Wedge