Honeywell MS9535-5 User Manual - Page 26

Indicators, Audible, One Beep, Two Beeps, Three Beeps, Razzberry Tones - configuration guide

Get Honeywell MS9535-5 PDF manuals and user guides View all Honeywell MS9535-5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

SCANNER OPERATION Indicators Audible When the scanner is in operation, it provides audible feedback. These sounds indicate the status of the scanner. Eight settings are available for the tone of the beeper (normal, 6 alternate tones and no tone). To change the tones, refer to the MetroSelect Single-Line Configuration Guide (MLPN 00-02544x) or MetroSet2's help files. One Beep The scanner will beep once after communication has been established and the unit is properly placed into the cradle. When the scanner successfully reads a bar code, the scanner's white LED will flash and the unit will beep once. When the CodeGate button is pressed for 3 seconds, the scanner will indicate it has entered full sleep mode with a extended beep. Two Beeps When the scanner has a low battery voltage, it will emit two beeps after a successful scan and flash the amber LED every 5 seconds. When there is a Flash ROM upgrade needed, the scanner will beep twice followed by alternating flashing of the blue and white LEDs. When communication has been broken between the scanner and cradle, the scanner will emit two combined high and low tones while the blue LED flashes. Three Beeps When entering configuration mode, the white LED will flash while the scanner simultaneously beeps three times. When exiting configuration mode, the scanner will beep three times and the white LED will stop flashing. When using single-code-Configuration, the scanner will sound a 3-combination tone (a short pause followed by a high tone and a low tone). This indicates a single configuration bar code has successfully configured the scanner. When scanning a Bluetooth address bar code, the scanner will beep three times. The scanner's blue LED will start to flash as it attempts to establish a communication link. The scanner will emit a 3-combination tone and the blue LED will stop flashing, staying steadily illuminated to indicate communication between the scanner and the cradle has been successfully established. Razzberry Tones This tone indicates a type of failure. Refer to "Failure Modes" on page 25. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
22
S
CANNER
O
PERATION
Indicators
Audible
When the scanner is in
operation, it provides audible feedback.
These sounds
indicate the status of the scanner
.
Eight settings are available for the tone of the
beeper (normal, 6 alternate tones and no tone).
To change the tones, refer to
the MetroSelect
Single-Line Configuration Guide (
MLPN
00-02544
x
) or
MetroSet2’s help files.
One Beep
The scanner will beep once after communication has been
established and the unit is properly placed into the cradle.
When the scanner
successfully
reads a bar code, the scanner’s white
LED will flash and the unit will beep once.
When the CodeGate button is pressed for 3 seconds, the scanner will
indicate it has entered
full sleep mode
with a extended beep.
Two Beeps
When the scanner has a low battery voltage, it will emit two beeps
after a successful scan and flash the amber LED every 5 seconds.
When there is a Flash ROM upgrade needed, the scanner will beep
twice followed by alternating flashing of the blue and white LEDs.
When communication has been broken between the scanner and
cradle, the scanner will emit two combined high and low tones while
the blue LED flashes.
Three Beeps
When entering configuration mode, the white LED will flash while the
scanner simultaneously beeps three times.
When exiting configuration mode, the scanner will beep three times
and the white LED will stop flashing.
When using single-code-Configuration, the scanner will sound a
3-combination tone (a short pause followed by a high tone and a low
tone).
This indicates a single configuration bar code has successfully
configured the scanner.
When scanning a Bluetooth address bar code, the scanner will beep
three times. The scanner’s blue LED will start to flash as it attempts to
establish a communication link. The scanner will emit a 3-combination
tone and the blue LED will stop flashing, staying steadily illuminated
to indicate communication between the scanner and the cradle has
been successfully established.
Razzberry Tones
This tone indicates a type of failure.
Refer to “Failure Modes" on
page
25
.