Intel SBXD62 User Guide - Page 29

Removing the Blade Server Bezel Assembly, Installing a SAS Hard Disk Drive

Get Intel SBXD62 - Server Compute Blade PDF manuals and user guides
UPC - 735858185448
View all Intel SBXD62 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Removing the Blade Server Bezel Assembly To install certain options, you must first remove the blade server bezel assembly. The following illustration shows how to remove the bezel assembly. Bezel-assembly release Bezel-assembly release Control panel connector Control-panel cable AF000438 To remove the blade server bezel assembly, complete the following steps: 1. Read the safety information beginning on page 65 in Appendix C, "Safety Information" and "Installation Guidelines" on page 15. 2. Open the blade server cover (see "Opening the Blade Server Cover" on page 18 for instructions). 3. Press the bezel-assembly release and pull the bezel assembly away from the blade server approximately 1.2 cm (0.5 inch). 4. Disconnect the control-panel cable from the control-panel connector. 5. Pull the bezel assembly away from the blade server. 6. Store the bezel assembly in a safe place. Installing a SAS Hard Disk Drive The blade server has two connectors on the system board for installing optional SFF SAS hard disk drives. Each SAS connector is on the same bus. Depending on the blade server model, at least one SAS hard disk drive might already be installed. If the blade server is equipped with one SAS hard disk drive, you can install an additional SAS hard disk drive. These two SAS hard disk drives can be used to implement and manage a redundant array of independent disks (RAID) level-1. See "Configuring a SCSI RAID Array" on page 42 for information about SCSI RAID configuration. Intel® Server Compute Blade SBXD62 Installation and User's Guide 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Intel® Server Compute Blade SBXD62 Installation and User’s Guide
19
Removing the Blade Server Bezel Assembly
To install certain options, you must first remove the blade server bezel assembly. The
following illustration shows how to remove the bezel assembly.
To remove the blade server bezel assembly, complete the following steps:
1.
Read the safety information beginning on
page 65 in Appendix C, “Safety
Information”
and
“Installation Guidelines” on page 15
.
2.
Open the blade server cover (see
“Opening the Blade Server Cover” on page 18
for
instructions).
3.
Press the bezel-assembly release and pull the bezel assembly away from the blade
server approximately 1.2 cm (0.5 inch).
4.
Disconnect the control-panel cable from the control-panel connector.
5.
Pull the bezel assembly away from the blade server.
6.
Store the bezel assembly in a safe place.
Installing a SAS Hard Disk Drive
The blade server has two connectors on the system board for installing optional SFF SAS
hard disk drives.
Each SAS connector is on the same bus. Depending on the blade server model, at least one
SAS hard disk drive might already be installed. If the blade server is equipped with one
SAS hard disk drive, you can install an additional SAS hard disk drive. These two SAS
hard disk drives can be used to implement and manage a redundant array of independent
disks (RAID) level-1. See
“Configuring a SCSI RAID Array” on page 42
for information
about SCSI RAID configuration.
Control panel
connector
Bezel-assembly
release
Bezel-assembly
release
Control-panel
cable
AF000438