JVC TK-AM200U TK-AM200 Dome CCTV Camera Instruction Manual (748KB) - Page 15

JVC TK-AM200U - Active Movement Color Dome Camera Manual

Get JVC TK-AM200U - Active Movement Color Dome Camera PDF manuals and user guides View all JVC TK-AM200U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

INSTALLATION Ceiling Installation 1. 75mm 2. To ceiling slab or channel Wire M3 screw Safety wire attachment hole 3 mm or less. 3. 3.-1) Guide Tab 3.-1) Guide Tab 3.-2) Connector cable White wire Make a hole (75 mm diameter) in the ceiling for passing the connection cables. 2. Attach the provided ceiling mount to the ceiling. ● Attach the ceiling mount so that the camera direction mark is aligned with the direction in which you want the camera to face. Coincide the center of the mount with the hole (75 mm diameter) for passing the cables through the ceiling. Attach the ceiling mount to the ceiling using 4 screws. ● Use M4 screws or bolts for attaching the Camera ceiling mount. direction ● If wood screws are used, use screws with mark a diameter of 4.1 mm. ● The screw head height should be no more than 3 mm. CAUTION: To prevent the ceiling mount and camera from dropping down, it is recommended to connect the ceiling mount to a ceiling slab or channel with a wire. Fasten the wire to the safety wire attachment hole using an M3 screw as shown in the illustration. 1. 3. Connector on terminal board 4. Hook Drop prevention wire Pass the wired terminal board through the hole in the ceiling mount and attach it to the camera body. 1) Slide the tab on the terminal board into the guide on the camera. When the terminal board is moved in the direction of the arrow, it is secured to the camera. 2) Connect the connector cable from the camera body to the connector on the terminal board. 4. Attach the drop prevention wire. As shown in the illustration, pull the drop prevention wire out from the ceiling mount and attach it to the drop prevention wire hook on the underside of the camera body. Memo: Bundling the drop prevention wire together with the cables connected to the terminal board using vinyl tape will help prevent the cables from being pinched. CAUTION Be sure to attach the drop prevention wire. If not attached, the camera body could drop down. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
15
Double
figures
Single
figures
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
"1"
"0"
●
Switch 4: Synchronization signal
selector switch
Switches the synchronization method
of the camera image.
OFF:
Internal synchronization (INT)
ON:
The camera’s vertical synchroniza-
tion is matched with the frequency
of the AC 24V line power supply.
When switching between mul-
tiple cameras using a switcher,
selecting this mode and adjust-
ing the vertical phase can re-
duce the monitor sync distur-
bances occurring when the
camera image is switched. (This
cannot be used in regions where
the power frequency is 50 Hz.)
●
Switches 5, 6, 7, 8
These switches are not used.
(Set them to OFF.)
4.
Camera ID setting switches
Camera ID setting is only performed
when the system connection selector
switches (Switch 1 and 2) are set to “RM-
P2580”.
The camera ID number is a number to
identify each of the cameras connect to
the RM-P2580. The camera ID number
should be the same as the number of
the RM-P2580 VIDEO INPUT terminal
to which the camera is connected.
Example:
The camera connected to VIDEO
INPUT 1 is set
to “01” as shown
on the right.
Memo:
If the camera ID numbers of cameras connect
to the RM-P2580 are duplicated, the system
will not work correctly.
5.
When setting of the switches is com-
pleted, close the cover over the setting
switches again.
Memo:
Switch 1 and 2 are used to specify the
form of the control signal cable connection
between the remote control unit and the
camera and the communication protocol.
Switch 1 (Initial setting: OFF)
OFF:
POINT TO POINT
ON:
MULTIDROP
Switch 2: (Initial setting: OFF)
OFF:
DUPLEX
(two-way data transmission)
ON:
SIMPLEX
(one-way data transmission)
●
Switch 3: Termination ON/OFF
switch
This is a termination ON/OFF switch
between the “RX+” and “RX–” control
signal connection terminals.
ON:
The “RX+” to “RX–” route is ter-
minated by a 110
Ω
resistor.
OFF: The
RX+
to
RX–
route is not
terminated.
(Initial setting: OFF)
In a system using the Remote Control Unit
RM-P2580, set this to “ON” only on the
camera placed at the end of the control sig-
nal cable. Set to OFF on all other cameras.
3.
Set system setting switches.
Set the system connection selector
switches (Switch 1, 2) in accordance
with the equipment that the camera
body is to be connected to.
Connecting
equipment
Switch 1
Switch 2
RM-P2580
ON
OFF
●
Switch 1, 2: System connection
selector switch
1
2
3
4
5
6
7
8
1
ON
1
OFF
Switches
ON
Switch numbers