Linksys WAG54G User Guide - Page 26

Network Setup - router

Get Linksys WAG54G - Wireless-G ADSL Gateway Wireless Router PDF manuals and user guides View all Linksys WAG54G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Wireless-G ADSL Gateway • MTU. The MTU (Maximum Transmission Unit) setting specifies the largest packet size permitted for network transmission. Select Manual and enter the value desired. It is recommended that you leave this value in the 1200 to 1500 range. By default, MTU is configured automatically. Network Setup • Router IP. The values for the Gateway's Local IP Address and Subnet Mask are shown here. In most cases, keeping the default values will work. • Local IP Address. The default value is 192.168.1.1. • Subnet Mask. The default value is 255.255.255.0. • Network Address Server Settings (DHCP). A Dynamic Host Configuration Protocol (DHCP) server automatically assigns an IP address to each computer on your network for you. Unless you already have one, it is highly recommended that you leave the Gateway enabled as a DHCP server. • Local DHCP Server. DHCP is already enabled by factory default. If you already have a DHCP server on your network, set the Gateway's DHCP option to Disable. • Starting IP Address. Enter a value for the DHCP server to start with when issuing IP addresses. This value must be 192.168.1. 2 or greater, because the default IP address for the Gateway is 192.168.1.1. • Number of Address. Enter the maximum number of computers that you want the DHCP server to assign IP addresses to. This number cannot be greater than 253. By default, as shown in Figure 5-9, the range is 192.168.1.100 to 192.168.1.149. • DHCP Address Range. The range of DHCP addresses is displayed here. • Client Lease Time. Enter the minutes in the field. • Time Setting. This is where you set the time zone for your Gateway. When finished making your changes on this tab, click the Save Settings button to save these changes, or click the Cancel Changes button to undo your changes. Figure 5-9: Optional Settings Chapter 5: Configuring the Gateway 19 The Setup Tab

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
19
Chapter 5: Configuring the Gateway
The Setup Tab
Wireless-G ADSL Gateway
•
MTU. The MTU (Maximum Transmission Unit) setting specifies the largest packet size permitted for network
transmission. Select
Manual
and enter the value desired. It is recommended that you leave this value in the
1200 to 1500 range. By default, MTU is configured automatically.
Network Setup
•
Router IP. The values for the Gateway’s Local IP Address and Subnet Mask are shown here. In most cases,
keeping the default values will work.
•
Local IP Address. The default value is 192.168.1.1.
•
Subnet Mask. The default value is 255.255.255.0.
•
Network Address Server Settings (DHCP). A Dynamic Host Configuration Protocol (DHCP) server automatically
assigns an IP address to each computer on your network for you. Unless you already have one, it is highly
recommended that you leave the Gateway enabled as a DHCP server.
•
Local DHCP Server. DHCP is already enabled by factory default. If you already have a DHCP server on your
network, set the Gateway’s DHCP option to
Disable
.
•
Starting IP Address. Enter a value for the DHCP server to start with when issuing IP addresses. This value
must be 192.168.1. 2 or greater, because the default IP address for the Gateway is 192.168.1.1.
•
Number of Address. Enter the maximum number of computers that you want the DHCP server to assign IP
addresses to. This number cannot be greater than 253. By default, as shown in Figure 5-9, the range is
192.168.1.100 to 192.168.1.149.
•
DHCP Address Range. The range of DHCP addresses is displayed here.
•
Client Lease Time. Enter the minutes in the field.
•
Time Setting. This is where you set the time zone for your Gateway.
When finished making your changes on this tab, click the
Save Settings
button to save these changes, or click
the
Cancel Changes
button to undo your changes.
Figure 5-9: Optional Settings