Netgear WN604-100NAS Reference Manual - Page 95

Troubleshooting and Debugging, No lights are lit on the wireless access point.

Page 95 highlights

Chapter 6 Troubleshooting and Debugging This chapter provides information about troubleshooting your NETGEAR Wireless N150 Access Point WN604. After each problem description, instructions are given to help you diagnose and solve the problem. For the common problems listed, go to the section indicated. • Is the WN604 on? Go to "Installing the WN604 Wireless Access Point" on page 2-3 • Have I connected the wireless access point correctly? Go to "Installing the WN604 Wireless Access Point" on page 2-3. • I cannot remember the wireless access point's configuration password. Go to "Changing the Administrator Password" on page 4-6. Note: For up-to-date WN604 installation details and troubleshooting guidance visit http:/ /kbserver.netgear.com/products/WN604.asp. If you have trouble setting up your WN604, check the tips below. No lights are lit on the wireless access point. It takes a few seconds for the power indicator to light up. Wait a minute and check the power light status on the access point. If the access point has no power. • Make sure the power cord is connected to the access point. • Make sure the power adapter is connected to a functioning power outlet. If it is in a power strip, make sure the power strip is turned on. If it is plugged directly into the wall, verify that it is not a switched outlet. • Make sure you are using the correct NETGEAR power adapter supplied with your access point. 6-1 v1.0, March 2010

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110

6-1
v1.0, March 2010
Chapter 6
Troubleshooting and Debugging
This chapter provides information about troubleshooting your NETGEAR Wireless N150 Access
Point WN604. After each problem description, instructions are given to help you diagnose and
solve the problem. For the common problems listed, go to the section indicated.
Is the WN604 on?
Go to
“Installing the WN604 Wireless Access Point” on page 2-3
Have I connected the wireless access point correctly?
Go to
“Installing the WN604 Wireless Access Point” on page 2-3
.
I cannot remember the wireless access point’s configuration password.
Go to
“Changing the Administrator Password” on page 4-6
.
If you have trouble setting up your WN604, check the tips below.
No lights are lit on the wireless access point.
It takes a few seconds for the power indicator to light up. Wait a minute and check the power light
status on the access point.
If the access point has no power.
Make sure the power cord is connected to the access point.
Make sure the power adapter is connected to a functioning power outlet. If it is in a power
strip, make sure the power strip is turned on. If it is plugged directly into the wall, verify that it
is not a switched outlet.
Make sure you are using the correct NETGEAR power adapter supplied with your access
point.
Note:
For up-to-date WN604 installation details and troubleshooting guidance visit
http:/
/kbserver.netgear.com/products/WN604.asp
.