Panasonic BT-LH2170 Operating Instructions

Panasonic BT-LH2170 Manual

Get Panasonic BT-LH2170 PDF manuals and user guides View all Panasonic BT-LH2170 manuals
Add to My Manuals
Save this manual to your list of manuals

Panasonic BT-LH2170 manual content summary:

  • Panasonic BT-LH2170 | Operating Instructions - Page 1
    Operating Instructions LCD Video Monitor Model No. BT-LH2170P Model No. BT-LH2170E DEUTSCH FRANÇAIS ITALIANO ESPAÑOL manual is also contained as a PDF file on the CD-ROM supplied with the unit. (Back cover) Before operating this product, please read the instructions carefully and save this manual
  • Panasonic BT-LH2170 | Operating Instructions - Page 2
    this first ! (for BT-LH2170P) WARNING: This equipment 100 - 240 V AC. Voltages other than 120 V are not intended for U.S.A. and Canada. CAUTION: Excessive sound pressure from earphones and headphones can cause hearing loss. CAUTION: This Monitor is for use only with Panasonic Wall Mount Adaptor, BT
  • Panasonic BT-LH2170 | Operating Instructions - Page 3
    ! (for BT-LH2170P) (continued) installed and used in accordance with the instruction manual, may cause harmful interference to radio communications for long periods of time. 14) R efer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
  • Panasonic BT-LH2170 | Operating Instructions - Page 4
    ! (for BT-LH2170E) WARNING: This do not remove covers. No user serviceable parts inside. Refer servicing to qualified service personnel. indicates safety information. CAUTION: hearing loss. CAUTION: This Monitor is for use only with Panasonic Wall Mount Adaptor, BT-WMA17G. Use with other Wall
  • Panasonic BT-LH2170 | Operating Instructions - Page 5
    ! (for BT-LH2170E) (continued) A replacement fuse cover can be purchased from your local Panasonic Dealer. How to replace the fuse 1. Open the fuse during recording or while On Air. 2. If the device is a Studio Monitor: A Power Management function may cause video for the confirmation of whether a
  • Panasonic BT-LH2170 | Operating Instructions - Page 6
    (for BT-LH2170E) ( signal connecting cables If your apparatus supports AES/EBU serial digital audio signals, must be attached on cable(s) following instructions in this manual. 3. Performance level The performance level 1000 2 Cd 0,01 100 3 Hg 0,1 1000 4 Cr6 0,1 1000 5 PBB 0,1
  • Panasonic BT-LH2170 | Operating Instructions - Page 7
    LCD panel to strong pressure may result in blurring or other damage. About this instruction manual • This instruction manual refers to BT-LH2170P/BT-LH2170E 00) in this manual. Precautions for Use • The LCD monitor is manufactured with use. • This unit does not support VIERA Link. When the unit
  • Panasonic BT-LH2170 | Operating Instructions - Page 8
    BT-LH2170P 2 Read this first ! (for BT-LH2170E 4 Transportation precautions 7 About this instruction manual 7 Precautions for Use 7 Standard accessories · Optional units 9 Outline 9 Dimensions 10 Controls and Their Functions 11 Video monitor (PICTURE) menu 21 Audio volume 21 User Data 22
  • Panasonic BT-LH2170 | Operating Instructions - Page 9
    BT-LH2170P/BT-LH2170E is a compact, flat panel LCD monitor for broadcast and industrial applications, equipped with a 54.6 cm (21.5 inch) (effective display area) LCD display. „„High performance LCD panel This product incorporates a full HD (1920 x 1080) LCD signals. Furthermore, support is also
  • Panasonic BT-LH2170 | Operating Instructions - Page 10
    15/16) 4-M3 260(10-1/4) 510(20-1/16) 475.2(18-5/8) 267.3(10-1/2) 163.5(6-7/16) 72 (2-13/16) 2.5(1/8) 27(1-1/16) 42.5(1-5/8) 100 (3-15/16) 4-M4 P=0.7 22.2(7/8) 209.5(8-1/4) 156(6-1/8) 388(15-1/4) 15(9/16) • When the unit will be permanently installed in one place, we recommend securing
  • Panasonic BT-LH2170 | Operating Instructions - Page 11
    Controls and Their Functions Video monitor Front panel 1 Rear panel 2 Front panel (→page 12) 1 Tally Lamp have been provided to enable attachment of a permanent protective panel. The LCD panel is shipped in packaging material to protect it from damage during unpacking and transportation
  • Panasonic BT-LH2170 | Operating Instructions - Page 12
    Serial digital interface input (compatible with 3G/ HD/SD) SDI2 : Serial digital interface input (HD/SD compatible) HDMI : HDMI input (HDCP compatible output jack (M3 stereo mini jack)*1 Allows you to connect headphones to monitor analog audio, SDI and HDMI signal inputs. • The sound volume and
  • Panasonic BT-LH2170 | Operating Instructions - Page 13
    1 SDI terminal A SDI1 (3G/HD/SD) input terminal (BNC) This is the SDI input terminal. (Compatible with 3G-SDI and 3G/HD/SD automatic switching) In 3D assist mode input and output terminals allows operation of multiple monitors (up to 32 monitors). • Connect a terminator (120 Ω) between the first
  • Panasonic BT-LH2170 | Operating Instructions - Page 14
    • If the power cover has come off or been removed, do not use the monitor with the power supply connected to both AC input and DC input terminals. • Use a external DC power supply and those of the DC IN socket of this monitor to ensure that a connection will maintain the correct polarity. If +12
  • Panasonic BT-LH2170 | Operating Instructions - Page 15
    or table with a soft cloth or similar material spread underneath. • The stand is specifically designed for this monitor and cannot be used with other monitors. The stands supplied with the BT-LH1700W/ 1710/1760 series cannot be used with this unit. Detaching the stand Attaching the stand Stand
  • Panasonic BT-LH2170 | Operating Instructions - Page 16
    code (TC) display, closed caption (CC) display, IMD (in monitor display) display and other information. Operating status display 1 2 SDI1 1080 using [SETUP LOAD] or [POWER ON SETUP].(→page 21) 8. Various indications (ANALOG mode) • Indicates that instructions on button operations. 16
  • Panasonic BT-LH2170 | Operating Instructions - Page 17
    On-screen Display (continued) 3. To close a menu, press . • The menu display disappears after approx. 2 minutes of inaction. (The value shown before the display clears is confirmed.) Picture adjusting (PICTURE) menu display [PICTURE] SETTING[FACTORY] A PEAKING 0 PHASE 31 * CHROMA
  • Panasonic BT-LH2170 | Operating Instructions - Page 18
    1080/60i Peak hold Overrange ●●In TWO WINDOW mode 1 21 2 3 43 4 5 65 6 7 87 8 45) • In 3D assist mode, you can monitor the left (L) channel of SDI1 audio. • In CD EF 01 • Use the menu to display the time code for HD-SDI signal input. It also allows you to switch between display modes:
  • Panasonic BT-LH2170 | Operating Instructions - Page 19
    CEA-608 (VBI), OP-42 • SD-SDI CC Standard EIA/CEA-608 (ANC/VBI), OP-42 • HD-SDI CC Standard EIA/CEA-608 type, display channel (EIA/CEA-608) and display service (EIA/CEA-708). (→page 46) • repositioned inside the screen area. • This monitor supports the TSL UMD PROTOCOL (Ver. 3.1 and Ver.
  • Panasonic BT-LH2170 | Operating Instructions - Page 20
    How to Use the On Screen Menu Main menu (MAIN MENU) • For details on how to open the main menu, refer to "Main menu (MAIN MENU)/FUNCTION menu/INPUT SELECT menu displays" (→page16). 1. Turn the rotary knob to select a menu item and press the rotary knob . [MAIN MENU] 2D/3D
  • Panasonic BT-LH2170 | Operating Instructions - Page 21
    (30) 0 to 60 (30) 0 to 60 (50) 0 to 100 (80) 1 to 30 (15) The text color of set values that values are white. Settings are loaded when the monitor is turned on. However, operations and changes MUTE]. • is displayed when audio output of the monitor is muted. • Audio volume is always available and
  • Panasonic BT-LH2170 | Operating Instructions - Page 22
    include the following settings. • Menu settings except [SETUP LOAD], [SETUP SAVE] and [REMOTE] in [CONTROL] (including button function settings on the monitor front panel) • Screen adjustments made with the rotary knob Saving user data 1. Press to display the main menu. Loading
  • Panasonic BT-LH2170 | Operating Instructions - Page 23
    TEMP. SHARPNESS MODE SHARPNESS H SHARPNESS V I-P MODE MONO ANAMO SD ASPECT SCAN ZEBRA INT.MIN. INT. MAX. EXT. MIN. VER. RS-485 ID SETUP RS-485 STX&ETX OPERATION LCD VIDEO NTSC SETUP DVI-I DIGITAL ANALOG COMPONENT LEVEL RGB- CHANNEL CAPTION SERVICE IN MONITOR DISPLAY POSITION CHAR. COLOR GPI CONTROL
  • Panasonic BT-LH2170 | Operating Instructions - Page 24
    area marker that is adjustable in 1% increments within a range of 80 to 100%. However, when the [MARKER TYPE] is [TYPE1], 88 % indicates HD and SD signal input when [SD ASPECT] is set to [16:9] aspect ratio mode. (→ 28 page "SD ASPECT") *4 These settings are enabled only for SD signal input when [SD
  • Panasonic BT-LH2170 | Operating Instructions - Page 25
    will not be visible if set to [100%]. *7 Display size for SD signals differ. TYPE1: The effective horizontal area meets the SMPTE ST125 for NTSC and ITU-R BT.601-5 for PAL. TYPE2: The effective horizontal area meets the EIA-RS170A for NTSC and ITU-R BT.470-4 for PAL. • Markers other than
  • Panasonic BT-LH2170 | Operating Instructions - Page 26
    % area marker 88 % area marker 80 % area marker (Displayed for HD input and SD input in 16:9 ratio mode.) This marker is displayed as a dotted at the center of the screen. 80 % area marker 80 % Area marker 100 % Area marker USER Area marker *1 VAR Area marker *2 „„Cross marker Cross marker
  • Panasonic BT-LH2170 | Operating Instructions - Page 27
    equivalent to a color temperature range of 3,000 K to 9,300 K) [D93] Equivalent to a color temperature of 9,300 K [D65] Equivalent to a color temperature of 6,500K [ adjusting) menu. *6 When HD signals are input via SDI1 and SD signals via SDI2 or SD signals via SDI1 and HD signals via SDI2 in
  • Panasonic BT-LH2170 | Operating Instructions - Page 28
    to 109% (Factory default setting: 100%) Description Selects IP conversion mode. at 0. With an Anamo lens and HD-SDI input, the picture is resized Sets the aspect ratio for SD signal input. [4:3] 4:3 IP conversion using intra-frame interpolation. This monitor suppresses the delay to within 1 field.
  • Panasonic BT-LH2170 | Operating Instructions - Page 29
    range of 3,000 K to 9,300 K) [D93] Equivalent to a color temperature of 9,300 K [D65] Equivalent to a [INT. ] 70% MIN. 85% MAX. [EXT. ] 5% 100% RETURN RETURN MIN. MAX. MENU EXIT • The above two screens cannot is also made if the monitor is left idle for 10 seconds. However, when called using
  • Panasonic BT-LH2170 | Operating Instructions - Page 30
    can be entered for this monitor. Only alphabetic characters (English), numeric characters and symbols can be used. *3 [USER1] to [USER 5] and [FACTORY] have the same factory defaults. *4 Factory default setting for the BT-LH2170P. *5 Factory default setting for the BT-LH2170E. *6 ITU-709 is an ITU
  • Panasonic BT-LH2170 | Operating Instructions - Page 31
    Main Menu (continued) „„INPUT NAME SETUP The INPUT NAME SETUP function allows you to change the names of the ([VIDEO], [SDI1], [SDI2], [HDMI], [DVI-I] ([YPBPR]/ [RGB-COMP.]/[DVI-VIDEO]/[DVI-COMP.]), [INT-SG]) input lines that are displayed in the status display or other indications. 1. Turn the
  • Panasonic BT-LH2170 | Operating Instructions - Page 32
    Main Menu (continued) „„CALIBRATION The CALIBRATION function in this monitor measures LCD panel characteristics from low to high brightness values and uses internal monitor processing to handle calibration. Calibration is performed using internal signals and do not rely on image quality settings.
  • Panasonic BT-LH2170 | Operating Instructions - Page 33
    Main Menu (continued) Performing AUTO CALIBRATION 1. Turn the rotary knob in the [SYSTEM CON- FIG] menu to select the [CALIBRATION] submenu and press the rotary knob . 2. Turn the rotary knob to select the [AUTO CALIBRATION] submenu and press the rotary knob .
  • Panasonic BT-LH2170 | Operating Instructions - Page 34
    FUNCTION1 FUNCTION5 Setting HV DELAY BLUE ONLY GAMMA SELECT SD ASPECT SCAN SUB WINDOW WFM/VECTOR MARKER WHITE BALANCE order. [GAMMA STANDARD] → [GAMMA FILM] → [GAMMA STDIO/PST GAMMA CINEMA] [SD ASPECT] *2*3 Switches between [16:9] and [4:3]. [SCAN] *2*3 Switches between [UNDER SCAN
  • Panasonic BT-LH2170 | Operating Instructions - Page 35
    Main Menu (continued) Submenu (continued from the previous page) Setting FUNCTION DISPLAY *8 OFF ON1 ON2 *9 Description [TIME CODE] *2 Turns the time code display on and off. [CLOSED CAPTION] *2 Turns the closed caption display on and off. For details on the available operation
  • Panasonic BT-LH2170 | Operating Instructions - Page 36
    Main Menu (continued) SD ASPECT Setting SCAN SUB WINDOW WFM/VECTOR MARKER WHITE are NO SIGNAL/UNSUPPORT SIGNAL • During GPI setting • Y MAP ON • During PC signal input When other than HD-SDI input • 3D ASSIST During PC signal input • NO SIGNAL PICTURE ASSIST ON • Y MAP ON • The TWO
  • Panasonic BT-LH2170 | Operating Instructions - Page 37
    STANDARD] → [GAMMA FILM] → [GAMMA STDIO/PST] → [GAMMA CINEMA] SD ASPECT [4:3]→[16:9] SCAN [NORMAL SCAN]→[UNDER SCAN] SUB WINDOW [SINGLE]→[FULL/PART]→[ MARKER*11 ] *10xx% indicates an 80 to 100% USER setting *11xx%/yy% is the VAR set value for 80 to 100 % aspect ratio • When the set values for
  • Panasonic BT-LH2170 | Operating Instructions - Page 38
    Main Menu (continued) „„FUNCTION skip function This function allows you to skip some of the functions assigned to FUNCTION during FUNCTION operation. When functions are assigned to to in the FUNCTION menu, a submenu that allows you to skip function settings appears. Turn [
  • Panasonic BT-LH2170 | Operating Instructions - Page 39
    (Y→R→G→B) VECTOR display*12 Press the same button again *12Displayed only for SDI signal input. • The scale display is as shown below. 100 % 50 % 0 % WFM (waveform display) VECTOR (vector display) These examples show 16:9 aspect ratio images. 109 % RED MAGENTA A dotted line indicates for
  • Panasonic BT-LH2170 | Operating Instructions - Page 40
    Main Menu (continued) „„ZEBRA The stripes of the ZEBRA function appear over an image (in the viewfinder) to help you adjust the aperture of a camera lens for optimum exposure and easily find the areas of an image that are overexposed and turn white (where clipping occurs). Press any of the <
  • Panasonic BT-LH2170 | Operating Instructions - Page 41
    inputs in separate windows (SDI1 in the left window and SDI2 in the right window). The function also displays the audio volume and the in-monitor display (IMD) for both SDI1 and SDI2. SDI1 and SDI2 are displayed at a fixed location. The screen switches at each press of a to
  • Panasonic BT-LH2170 | Operating Instructions - Page 42
    720/50p in the single screen mode, the number of pixels of the monitor panel is greater than the number of samples of the input signal. Although the CROSS HATCH function is assigned changes the display as shown. HD/SD (16:9) mode SD (4:3) mode Press the same button again Dim cross hatch Press
  • Panasonic BT-LH2170 | Operating Instructions - Page 43
    INPUT SEL. SDI1 INPUT SEL. SDI2 INPUT SEL. HDMI INPUT SEL. DVI-I INPUT SEL. INT-SG SD ASPECT SCAN R-TALLY G-TALLY MONO GAMMA SEL. FILM GAMMA SEL. STDIO/PST GAMMA SEL. CINEMA PIXEL TO Operation may not be possible depending on the setting conditions. Example: SD ASPECT operation when input signal is
  • Panasonic BT-LH2170 | Operating Instructions - Page 44
    -I analog inputs. [SMPTE] Signal level complies with SMPTE, and PB, PR are 0.7 V [p-p] at 100% chroma. [B75] Select this when connecting a Betacam or similar device with a setup function. (The monitor internally adjusts the 7.5 % setup level to suit the black level) [B00] Select this when
  • Panasonic BT-LH2170 | Operating Instructions - Page 45
    of the menu settings. During SD-SDI signal input, the display becomes [4CH] even if [8CH] is selected in the menu. *8 During analog signal input, the reference point is 20 dB regardless of menu setting. *9 Factory default setting for the BT-LH2170E. *10Factory default setting for the BT-LH2170P. 45
  • Panasonic BT-LH2170 | Operating Instructions - Page 46
    8x VECTOR SCALE 75% 100% Determines the scale of vector waveform. [75%] Displays it at 75 % scale. [100%] Displays it at 100 % scale. TIME CODE input. *2 When the TWO WINDOW function is operating, only SDI1 signals support time code display. As a result, the time code is displayed at the
  • Panasonic BT-LH2170 | Operating Instructions - Page 47
    Main Menu (continued) Submenu CAPTION SERVICE IN MONITOR DISPLAY POSITION CHAR. COLOR Setting SRV1 SRV2 SRV3 SRV4 SRV5 SRV6 OFF ON TOP BOTTOM CMD WHITE BLUE GREEN YELLOW CYAN RED GRAY MAGENTA Description Selects the closed caption display service for [CEA-708]. Selects whether to enable or
  • Panasonic BT-LH2170 | Operating Instructions - Page 48
    be placed. *1 Only available when [REMOTE] is selected under [CONTROL]. *2 The monitor supports version 3.1 and 4.0 of the TSL UMD PROTOCOL provided by Television System LTD. HOURS METER Submenu OPERATION LCD Setting xxxxxxh *1 xxxxxxh *1 Description Displays the total number of hours it has
  • Panasonic BT-LH2170 | Operating Instructions - Page 49
    basic 3D camera adjustments. (Half-mirror type supported) Shifts SDI2 (R) image horizontally and vertically . Switches the L/R images automatically or manually to enable the convergence point to be open the [PICTURE] (picture adjusting) menu. (→page 21) 1 3D ASSIST - MIRROR- SDI1(L): 1080/60i(L)
  • Panasonic BT-LH2170 | Operating Instructions - Page 50
    3D Assist Mode (continued) „„How to return to 2D mode Select [2D] in [2D/3D ASSIST] in [MAIN MENU] (main menu) or use the button or use [2D/3D ASSIST] in the [FUNCTION] menu to select it. MIRROR (Left/Right and Top/Bottom inversion) This function performs left/right, top/bottom and
  • Panasonic BT-LH2170 | Operating Instructions - Page 51
    switch the SDI1 (L) image and SDI2 (R) image and then check the subject's position. Screen: Normal display of one screen [3D ASSIST] CONVERGENCE MANUAL MANUAL L SPEED SLOW MENU EXIT RETURN RETURN • The place at which the image does not change is the conver- gence point
  • Panasonic BT-LH2170 | Operating Instructions - Page 52
    3D Assist Mode (continued) COLOR (Color Check) This function overlays and displays the SDI1 (L) image and SDI2 (R) image on a checkerboard pattern in one screen to enable you to check the brightness offset and color differences Screen: Overlay L/R on one screen. [3D ASSIST] COLOR SIZE 256 <
  • Panasonic BT-LH2170 | Operating Instructions - Page 53
    3D Assist Mode (continued) VERTICAL (Vertical Offset Check) This function enables you to operate two horizontal line markers to check the number of lines between markers in the displayed image and check vertical offset. Screen: The L/R 2 screens are shown side-by-side, and two markers are shown.
  • Panasonic BT-LH2170 | Operating Instructions - Page 54
    3D Assist Mode (continued) Menu OVERLAY MKR POSI MKR WIDTH Setting STANDARD GLAY COLOR 0 to 56 (MKR WIDTH 3% setting) 0 to 37 (MKR WIDTH 2% setting) 0 to 18 (MKR WIDTH 1% setting) (Factory default setting: 0) 3% 2% 1% Underlined values indicate factory defaults. Description Selects overlay or
  • Panasonic BT-LH2170 | Operating Instructions - Page 55
    )  Setting item 2D/3D ASSIST DVI-I Input terminal VIDEO SDI1/SDI2 HDMI ANALOG RGBCOMP. YPBPR DIGITAL COMP. VIDEO - SD HD COMP. SD HD - SD HD - SD HD MARKER MARKER *1*2 16:9 *1*2 4:3 *1*2 BACK *1*2 CENTER *1*2 CROSS *1*2 COLOR *1*2 GPI MARKER1 GPI MARKER2 MARKER TYPE *1*2 CROSS HATCH
  • Panasonic BT-LH2170 | Operating Instructions - Page 56
    Can be set) DVI-I  Setting item Input terminal VIDEO SDI1/SDI2 HDMI ANALOG RGBCOMP. YPBPR DIGITAL COMP. VIDEO - SD HD COMP. SD HD - SD HD - SD HD SUB WINDOW üüü üü üü üü MENU POSITION STATUS DISPLAY INPUT NAME SETUP SYSTEM CONFIG SETUP LOAD SETUP SAVE POWER ON SETUP
  • Panasonic BT-LH2170 | Operating Instructions - Page 57
    CHANNEL ü CAPTION SERVICE ü*3 IN MONITOR DISPLAY ü POSITION LCD ü SDI1/SDI2 SD HD ü*3 ü ü*3 ü ü*3 ü ü*3 ü ü*3 ü HDMI COMP. SD ü*4 ü ü*3 ü*3 ü*3 ü*3 ü*3 ü*3 ü*3 ü*3 ü*3 ü*3 ü*3 ü*3 ü*3 ü*3 ü*3 ü*3 ü*3 ü*3 DVI-I ANALOG DIGITAL RGBCOMP. YPBPR COMP. VIDEO HD - SD HD - SD HD
  • Panasonic BT-LH2170 | Operating Instructions - Page 58
    SHARPNESS H SHARPNESS V VIDEO CONFIG I-P MODE MONO ANAMO SD ASPECT SCAN ZEBRA INT MIN. INT MAX. EXT MIN. COLOR SPACE POWER DOWN POWER SAVE MODE CALIBRATION SDI1/SDI2 HD ü ü ü ü ü Setting item Input terminal SERVICE IN MONITOR DISPLAY POSITION CHAR. COLOR SDI1/SDI2
  • Panasonic BT-LH2170 | Operating Instructions - Page 59
    Setting Item Restrictions (continued) (ü: Can be set) Setting item Input terminal CONTROL LOCAL ENABLE CONTROL PROTOCOL VER. RS-485 ID SETUP RS-485 STX&ETX HOURS METER OPERATION LCD SDI1/SDI2 HD 59
  • Panasonic BT-LH2170 | Operating Instructions - Page 60
    REMOTE Specifications This monitor enables remote operation via the GPI input terminal, the line to DVI-I. Switches the input line to INT-SG. Sets the aspect ratio for SD signal input. (Disabled during HD signal input) Switches the scan mode between UNDER and NORMAL. Lights the red tally. Lights
  • Panasonic BT-LH2170 | Operating Instructions - Page 61
    REMOTE Specifications (continued) Assigned item PIXEL TO PIXEL FOCUS-IN-RED ZEBRA REMOTE STANDBY *4*5 Function Switches screen display between input size and display size. Displays the outlines of the subject that are in focus in red Superimposes the ZEBRA pattern over an area of the image with
  • Panasonic BT-LH2170 | Operating Instructions - Page 62
    REMOTE Specifications (continued) RS-232C input terminal External operations can be performed via the RS-232C interface. For details on the pin arrangement and RS-232C input terminal connections, refer to the diagram below and the table below right. For details on specific systems using RS-232C
  • Panasonic BT-LH2170 | Operating Instructions - Page 63
    RS-485 input/output terminal pin arrangement and connections. TSL protocol version 3.1 and 4.0 are supported. Make sure that the same TSL protocol versions are used on external control devices and the monitor. For information on specific systems using RS-485 input terminals, contact your supplier
  • Panasonic BT-LH2170 | Operating Instructions - Page 64
    :SHP 19 VPC:SHH 20 VPC:SHV 21 MIP: 22 OMO: 23 MAS: 24 MSC:
  • Panasonic BT-LH2170 | Operating Instructions - Page 65
    x4 4:x8 DIS 62 DIS:VSC VECTOR SCALE 0:100 % 1:75 % DIS 63 DIS:TMP TIMECODE 7:GRAY 8:MAGENTA 68 DIS:IMV IN MONITOR DISPLAY 0:Ver3.1 1:Ver4.0 DIS VERSION 69 AUD [CC TYPE], [CAPTION CHANNEL], [CAPTION SERVICE] menu items under [DISPLAY SETUP] simultaneously.
  • Panasonic BT-LH2170 | Operating Instructions - Page 66
    REMOTE Specifications (continued) No Send commands 72 AUD:ISR Command name SELECT R 73 AUD:OSL 74 AMT: AUDIO OUT SEL. AUDIO MUTE Data 0:1ch/9ch 1:2ch/10ch 2:3ch/11ch 3:4ch/12ch 4:5ch/13ch 5:6ch/14ch 6:7ch/15ch 7:8ch/16ch 0:SDI1 1:SDI2 0:OFF
  • Panasonic BT-LH2170 | Operating Instructions - Page 67
    PHASE 00 to 60 6 QPC:VOL VOLUME 00 to 60 7 QBL BACKLIGHT 000 to 100 8 QMK:MAK MARKER*3 00:OFF 01:80 % 02:88 % 03:93 % 04 sharpness set value 20 QIP IP MODE 0:MODE1 1:MODE2 21 QMO MONO 1:OFF 2:ON 22 QAS SD ASPECT 0:16:9 1:4:3 23 QSC SCAN 0:NORMAL 1:
  • Panasonic BT-LH2170 | Operating Instructions - Page 68
    480/59.94p 17:480/59.94i 18:576/50p 20:1080/60p 21:1080/59.94p 22:1080/50p 23:720/50p 51:640x480 54:800x600 x4 4:x8 0:100 % 1:75 % 0:TOP 1: RIGHT 2:CENTER 3:LEFT 61 QTF 62 QMD 63 QMP TIMECODE FONT SIZE IN MONITOR DISPLAY IN MONITOR DISPLAY POSITION 0:LARGE
  • Panasonic BT-LH2170 | Operating Instructions - Page 69
    ) 1: WHITE 2: BLUE 3:GREEN 4:YELLOW 5:CYAN 6:RED 7:GRAY 8:MAGENTA 65 QMV IN MONITOR DISPLAY 0:Ver3.1 1:Ver4.0 VERSION 66 QAI INPUT SELECT 0:AUTO 1:ANALOG 67 QGS GROUP SELECT ON 71 QOS AUDIO OUT SEL. 0:SDI1 1:SDI2 72 QID MODEL CHECK BT-LH2170 69
  • Panasonic BT-LH2170 | Operating Instructions - Page 70
    are essential to keep the monitors in optimum condition and ensure safe operation. Be sure to conduct the following maintenance inspections to enable long-term and full use of all its functions. Necessity of periodic maintenance service The backlight in the LCD panel is a consumable component that
  • Panasonic BT-LH2170 | Operating Instructions - Page 71
    power supply input voltage has dropped below approximately 11.0 V. If the monitor has powered down, connect an external DC power supply providing 11.0 V and turn the POWER switch ON. Maintenance • Clean the cabinet and LCD panel by gently wiping them with a soft cloth. To remove stubborn soiling
  • Panasonic BT-LH2170 | Operating Instructions - Page 72
    274, 296, 259, ITU-R BT.656-4 compliant EMBEDDED AUDIO supported 3G-SDI: SMPTE ST 299 compliant 48 kHz, synchronous supported 16 channels supported HD-SDI: SMPTE ST 299 compliant 48 kHz, synchronous compatible 8 channels supported SD-SDI: SMPTE ST 272
  • Panasonic BT-LH2170 | Operating Instructions - Page 73
    1024 ü ü 1920×1080 ü*4 ü DIGITAL COMP. ü*7 *4 An HDMI 1920 × 1080 (60 Hz) PC signal is displayed as a 1080/60p VIDEO signal. *5 The frame frequency supports 60 Hz only. *6 The frame frequency is not displayed. *7 When [DVI-I] is set to [DIGITAL] and [DIGITAL] is set to [DVI-AUTO], 1080/60p
  • Panasonic BT-LH2170 | Operating Instructions - Page 74
    B-DS*1 2x1280x720 4:2:2(YCbCr) 10 *1 Displays only data stream 1. *2 The frame frequency of 1/1.001 is also supported. Interlaced Progressive Progressive Interlaced Progressive Interlaced Progressive Interlaced Progressive Interlaced Progressive Interlaced Progressive Progressive Progressive
  • Panasonic BT-LH2170 | Operating Instructions - Page 75
    Specifications (continued) „„List of Signal Formats Supported in 3D Assist Mode (ü: Supported) Input Signal Format/ Status SDI1/2 displays (SIMULTANEOUS) 720/50p ü 720/59.94p ü 720/60p ü 1035/59.94i*1 ü 1035/60i*2 ü 1080/23.98PsF ü 1080/24PsF ü 1080/
  • Panasonic BT-LH2170 | Operating Instructions - Page 76
    SD-SDI HD-SDI EIA/CEA-608 (VBI), OP-42 EIA/CEA-608 (VBI), EIA/CEA-608 (ANC), OP-42 EIA/CEA-608 (708), EIA/CEA-708, OP-47 Supported Specifications (EIA/CEA-608) Decode channels CC1 to CC4*2 Character Standard Character, Special Character Supported Specifications (EIA/CEA-708) Caption service
  • Panasonic BT-LH2170 | Operating Instructions - Page 77
    Specifications (continued) „„INT-SG (Internal chart for adjustment) 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% GRAY YELLOW CYAN 75% 75% 75% GREEN MAGENTA RED 75% 75% 75% BLUE 75% BLUE75% BLACK MAGENTA 75% BLACK CYAN75% BLACK GRAY75% -I WHITE +Q BLACK BLACK
  • Panasonic BT-LH2170 | Operating Instructions - Page 78
    21 C CALIBRATION 30, 32 CAPTION CHANNEL 46 CAPTION SERVICE 47 CC TYPE 46 CENTER 25 Center marker 26 CHAR. COLOR 47 CH INFO 45 CHROMA 21 MONITOR LCD 48 LEVEL 52 LEVEL METER 34, 45 LOCAL ENABLE 48 M Main menu 16, 20, 23 MAIN MENU 16, 20 Maintenance 71 Maintenance Inspections 70 MANUAL
  • Panasonic BT-LH2170 | Operating Instructions - Page 79
    53, 54 P PEAKING 21 PHASE 21, 44 PICTURE 12 Picture adjusting menu 17, 21 PICTURE ASSIST 35, 41 PICTURE menu 17, 21 PIXEL POSITION 34, 42 485 input/output terminals 13, 63 RS-485 STX&ETX 48 S SCAN 28, 34 SD ASPECT 28, 34 SDI1 (L 50 SDI2 (R 50 SDI terminal 13 SELECT L 45 SELECT
  • Panasonic BT-LH2170 | Operating Instructions - Page 80
    this product, please contact your local authorities or dealer and ask for the correct method of disposal. ENGLISH „„How to open the operating instruction manual PDF files Discontinue installation if the installation screen of the software opens as a result of inserting the CD-ROM. When [INDEX
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
SS0812KT0 -PS
Printed in Japan
ENGLISH
Model No.
BT-LH2170P
Model No.
BT-LH2170E
Operating Instructions
LCD Video Monitor
VQT4M18
Before operating this product, please read the instructions carefully and save this manual for future use.
DEUTSCH
Für Erlauterungen in Deutsch, konsultieren Sie bitte die mitgelieferte CD-ROM.
(Zurück Decke)
FRANÇAIS
Pour des explications en français, veuillez vous reporter au CD-ROM fourni.
(Quatrième de couverture)
ITALIANO
Per le istruzioni in italiano, vedere il CD-ROM in dotazione. (Retro della copertina)
ESPAÑOL
Para la explicación en español, consulte el CD-ROM suministrado. (Cubierta trasera)
This manual is also contained as a PDF file on the CD-ROM supplied with the unit. (Back cover)