Panasonic BT-LH2170 Operating Instructions - Page 39

Note on FULL/PART selection, WFM/VECTOR

Get Panasonic BT-LH2170 PDF manuals and user guides View all Panasonic BT-LH2170 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Main Menu (continued) Note on FULL/PART selection This function is designed to enable comparison of identical formats input to the same input terminal. Input of different formats via different input lines may distort the sub-window (left side, still image) or make part of the image disappear from view. However, input of an identical format signal to the input terminal during still image acquisition will display correctly. „„WFM/VECTOR The WFM/VECTOR function enables display of the waveform and vector display. Use [DISPLAY SETUP] in [MAIN MENU] (main menu) to select WFM and VECTOR display.(→page 46) Press the to (→page 12) button to which the WFM/VECTOR function has been assigned to switch displays in the following order. [WFM/VECTOR OFF] → [WFM Y ON] → [WFM R ON] → [WFM G ON] → [WFM B ON] → [VECTOR×1/×2S/×2/×4/×8] • To use the WFM/VECTOR function, it must be assigned to one of the to buttons. "WFM" signals are displayed in the following order: Y, R, G, B. Normal screen Press the same button again Press the button to which the WFM/VECTOR function has been assigned. WFM display (Y→R→G→B) VECTOR display*12 Press the same button again *12Displayed only for SDI signal input. • The scale display is as shown below. 100 % 50 % 0 % WFM (waveform display) VECTOR (vector display) These examples show 16:9 aspect ratio images. 109 % RED MAGENTA A dotted line indicates for each 10 % increase. ʵ4 % YELLOW GREEN I axis BLUE The frame is approx. 2.5 degrees and approx. 2.5%. Q axis CYAN The vertical lines in the frame are color coded to simplify identification. 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
39
Main Menu
(continued)
Note on FULL/PART selection
This function is designed to enable comparison of identical formats input to the same input terminal. Input of different formats via dif-
ferent input lines may distort the sub-window (left side, still image) or make part of the image disappear from view. However, input of
an identical format signal to the input terminal during still image acquisition will display correctly.
±
WFM/VECTOR
The WFM/VECTOR function enables display of the waveform and vector display. Use [DISPLAY SETUP] in [MAIN MENU] (main
menu) to select WFM and VECTOR display.(→page 46)
Press the <FUNCTION1> to <FUNCTION5> (→page 12) button to which the WFM/VECTOR function has been assigned to switch
displays in the following order.
[WFM/VECTOR OFF] → [WFM Y ON] → [WFM R ON] → [WFM G ON] → [WFM B ON] → [VECTOR×1/×2S/×2/×4/×8]
• To use the WFM/VECTOR function, it must be assigned to one of the <FUNCTION1> to <FUNCTION5> buttons.
“WFM” signals are displayed in the following order: Y, R, G, B.
Normal screen
Press the <FUNCTION> button to
which the WFM/VECTOR function
has been assigned.
WFM display
(Y→R→G→B)
VECTOR display
*
12
Press the same
button again
VECTOR
(vector display)
WFM (waveform
display)
These examples show 16:9 aspect ratio images.
*
12
Displayed only for SDI signal input.
• The scale display is as shown below.
100 %
109 %
A dotted line
indicates for
each 10 %
increase.
－
4 %
50 %
0 %
I axis
Q axis
BLUE
The frame is approx.
2.5 degrees and
approx. 2.5%.
MAGENTA
RED
YELLOW
GREEN
CYAN
The vertical lines in the frame are color coded to simplify
identification.
Press the same button again