Panasonic BT-LH2170 Operating Instructions - Page 34
FUNCTION, continued, Submenu, Setting, Description
View all Panasonic BT-LH2170 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 34 highlights
Main Menu (continued) FUNCTION Submenu FUNCTION1 FUNCTION5 Setting HV DELAY BLUE ONLY GAMMA SELECT SD ASPECT SCAN SUB WINDOW WFM/VECTOR MARKER WHITE BALANCE PIXEL TO PIXEL PIXEL POSITION FOCUS-IN-RED LEVEL METER CROSS HATCH MONO BLACK MODE TIME CODE CLOSED CAPTION AUDIO MUTE AUDIO OUT SEL. ANAMO TWO WINDOW Y MAP PICTURE ASSIST R COLOR G COLOR B COLOR ZEBRA ZEBRA LEVEL 2D/3D ASSIST UNDEF (Factory defaults FUNCTION1: WFM/VECTOR FUNCTION2: TWO WINDOW FUNCTION3: FOCUS-IN-RED FUNCTION4: TIME CODE FUNCTION5: LEVEL METER) Underlined values indicate factory defaults. Description Selects functions to be assigned to - (front panel buttons or the [FUNCTION] menu). [HV DELAY] *1 This displays the blanking period. The display changes in the following order. [DELAY OFF] → [H DELAY] → [V DELAY] → [HV DELAY] [BLUE ONLY] *1 Cuts the red and green signals. Use this function to check phase (PHASE) and chroma (CHROMA). This button toggles between ON and OFF. [GAMMA SELECT] *2*3 Displays the gamma curve. The display changes in the following order. [GAMMA STANDARD] → [GAMMA FILM] → [GAMMA STDIO/PST GAMMA CINEMA] [SD ASPECT] *2*3 Switches between [16:9] and [4:3]. [SCAN] *2*3 Switches between [UNDER SCAN] and [NORMAL SCAN]. [SUB WINDOW] *1 Sets the split-screen function. The display changes in the following order. [SINGLE] → [FULL/PART] → [STILL] [WFM/VECTOR] *2 Displays waveform or vector display. For details on the available operation items, refer to page 36. [MARKER] *2*3*4 Display the marker. For details on the available operation items, refer to page 36. [WHITE BALANCE] RGB can be directly adjusted under [GAIN]/[BIAS] in WHITE BALANCE only when [VAR1] to [VAR3] are selected under [COLOR TEMP.]. [PIXEL TO PIXEL] Turns the PIXEL TO PIXEL function On and Off. [PIXEL POSITION] Positions the display of signals when PIXEL TO PIXEL is on. The display changes in the following order. [PIXEL TO PIXEL LEFT]→[PIXEL TO PIXEL CENTER]→ [PIXEL TO PIXEL RIGHT] [FOCUS-IN-RED]*3*5 Turns On/Off the function that highlights in red the portion of the image that is being focused. [LEVEL METER] *2 Turns the audio volume bar meter display On and Off. [CROSS HATCH] *2 Displays the cross hatch grid. The display changes in the following order. [CROSS HATCH OFF] → [CROSS HATCH LOW] → [CROSS HATCH HIGH] [MONO] *2*3 Switches between color and monochrome. [BLACK MODE] *1*6 This mode is for correcting black level errors and checking the gradation of dark areas. The brightness of the backlight is reduced and the contrast is increased so that up to 75 % of the input signal level has the same gamma curve as the [GAMMA SELECT] setting. The signal level of 75% or higher is clipped. *1 The settings are canceled when the power is turned OFF. *2 When these settings are changed, the menu settings will also change. *3 The control settings do not operate during GPI operation. *4 Not displayed when [16:9], [4:3] and [CENTER] are all [OFF] in the [MARKER] menu settings. *5 During FOCUS-IN-RED operation, use the rotary knob to change the detection sensitivity. The setting range is from 1 to 30, with a higher numerical value resulting in higher detection sensitivity (the focus becomes less sharp). *6 The bright picture is clipped. The back light and contrast cannot be adjusted. 34