Panasonic microP2 Handheld AVC-ULTRA HD Camcorder Operating Instructions Basic - Page 144
[NETWORK SETUP], Description of settings, SIDE CROP], [LETTER BOX], [SQUEEZE], ON], [OFF], 2.5MHz]
View all Panasonic microP2 Handheld AVC-ULTRA HD Camcorder manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 144 highlights
[SDI OUT CHAR] Item [SDI EDH] [HD SDI REMOTE] [DOWNCON MODE] [DOWNCON SETTING] [DETAIL] [VIDEO OUT] [H.DTL LEVEL] [V.DTL LEVEL] [DTL CORING] [H.DTL FREQ] [VIDEO OUT CHAR] [VIDEO OUT ZEBRA] [TC OUT] [TC OUTPUT REF] Chapter 6 Menu Operations - Menu list Description of settings Selects whether to superimpose characters on terminal output images. [ON]: Superimposes. [OFF]: Does not superimpose. ffFactory setting: [OFF] Selects whether to superimpose EDH when output from the terminal is SD signal (480i and 576i). [ON]: Superimposes. [OFF]: Does not superimpose. ffFactory setting: [ON] Sets whether to use the control function of recording operation for an external device (such as a recorder) connected to the terminal at HD SDI output. [ON]: Controls the recording operation of the external device. [OFF]: Does not control the recording operation of the external device. ffFactory setting: [OFF] Selects the mode of the down converter output signal mode from the or terminal in HD mode (1080P, 1080i, or 720P). [SIDE CROP], [LETTER BOX], [SQUEEZE] ffFactory setting: [LETTER BOX] Turns detail function for the down converter output signal [ON]/[OFF]. [ON], [OFF] The down converter output signal contains detail components set during HD signal processing. This setting superimposes the detail components exclusive to down converter output to that signal. ffFactory setting: [ON] Sets horizontal detail correction level for the down converter output signal. [0]...[31] ffFactory setting: [8] Sets vertical detail correction level for the down converter output signal. [0]...[31] ffFactory setting: [4] Sets the detail noise removal level. [0]...[15] ffFactory setting: [1] Selects the horizontal detail frequency. [2.5MHz], [3MHz], [3.5MHz], [4MHz], [4.5MHz] ffFactory setting: [3.5MHz] Selects the terminal output [ON]/[OFF]. [ON]: Performs output. [OFF]: Stops output. ffFactory setting: [OFF] Selects whether to superimpose characters on terminal output images. [ON]: Superimposes. [OFF]: Does not superimpose. ffFactory setting: [ON] Selects whether the zebra pattern is superimposed over the output video signals from the terminal. [ON]: Superimposes. [OFF]: Does not superimpose. ffFactory setting: [OFF] Sets the type of time code output from the terminal. [TCG]: Outputs the time code generator value of the camera at all times. [TCG/TCR]: Outputs the time code generator value for camera image output, and the time code value of the video being played back for video playback output. ffFactory setting: [TCG] Sets the output delay of time code output from the terminal. [RECORDING]: Outputs the recorded time code with no delay. This is used when performing simultaneous recording on two cameras with the time code of this camera as the master. [VIDEO OUT]: Matches to output images. ffFactory setting: [VIDEO OUT] [NETWORK SETUP] Configure the settings regarding the network. [4G/LTE PROPERTY] cannot be selected when the setting is not required on the connected 4G/LTE USB modem. Item [USB MODE SELECT] [USB MODE] Description of settings Sets the camera operation mode when an external device is connected to the USB. [STORAGE]: Sets the mode to be used with connected devices such as an external hard disk drive. [DEVICE]: Selects the USB device mode for using P2 cards as mass storage, using computers or other devices connected via USB 2.0. ffFactory setting: [STORAGE] Enables/disables the mode selected in [USB MODE SELECT]. [ON], [OFF] ffFactory setting: [OFF] - 144 -