Panasonic microP2 Handheld AVC-ULTRA HD Camcorder Operating Instructions Basic - Page 183

Chapter 9 Network Connection - Network settings [PRIMARY DNS]: Primary DNS server setting (Factory setting: [0.0.0.0]) (When [DHCP] is set to [ENABLE] and can be acquired from the DNS server, the DNS server value which is acquired externally is overwritten. When the value is [0.0.0.0], the server is not set.) [SECONDARY DNS]: Secondary DNS server setting (Factory setting: [0.0.0.0]) (When [DHCP] is set to [ENABLE] and can be acquired from the DNS server, the DNS server value which is acquired externally is overwritten. When the value is [0.0.0.0], the server is not set.) [DHCP SERVER]: Setting whether to use the DHCP SERVER function ([ENABLE]: Use the DHCP SERVER function/[DISABLE]: Does not use the DHCP SERVER function) (Factory setting: [ENABLE]) (cannot be set) 3 Select [WLAN] in the main menu → [NETWORK SETUP] → [NETWORK SEL]. If the setting is changed, the camera will restart as necessary. 4 Enter information on the wireless access point to connect to. Select [MANUAL] in the main menu → [NETWORK SETUP] → [WIRELESS PROPERTY] → [SSID INPUT MODE]. Enter SSID of the wireless access point for destination in [SSID] of the camera. Select the encryption method to be used from the camera's [ENCRYPTION]. ffFactory setting: [WPA2-AES] Enter a password of the wireless access point for destination in [ENCRYPT KEY] of the of the camera. 5 Check the network connection. When the setting is completed, confirm that network connection between the camera and the wireless access point is made properly. When network connection is made properly, the network status icon at the upper right of the thumbnail screen changes in yellow, and applications (P2 Browser, FTP client function) which require network can be used. @@NOTE tt There are following restrictions while wireless LAN is set. - Regardless of menu settings, signals are not output from the terminal. - The LCD monitor and viewfinder cannot be used together. If you close the LCD monitor, the viewfinder can be used. tt The startup time after turning on the power may be longer due to starting of the network. tt When you change the settings of [NETWORK SEL], the changes will not be reflected until the camera is restarted. After the settings have been changed, the setting screen termination may take time due to the restart of the network service. tt All of the IP address, subnet mask, and default gateway must be correctly set. If the warning [CANNOT ACCESS GATEWAY!] appears at the termination of the setting screen, contact the administrator of the network in use. tt If you do not use the default gateway and DNS, set them to [0.0.0.0]. tt DHCP and DNS may not function properly depending on the network environment. [INFRA] mode (when SSID is selected from the list) Use the following procedures when the wireless access point to connect to is selected from a list. 1 Select [INFRA] in main menu → [NETWORK SETUP] → [WIRELESS PROPERTY] → [TYPE]. 2 Set each item in main menu → [NETWORK SETUP] → [WIRELESS PROPERTY] as necessary. [MAC ADDRESS]: MAC address of wireless LAN (cannot be changed) [BAND]: Setting that switches between 2 transmission methods (2.4 GHz or 5 GHz) (Factory setting: [2.4GHz]) (Cannot be set) [CHANNEL (2.4GHz)]: Channel used when set to 2.4 GHz (Factory setting: [AUTO]) (Cannot be set) [CHANNEL (5GHz)]: Channel used when set to 5 GHz (Factory setting: [AUTO]) (Cannot be set) [DHCP]: Setting whether to use automatic acquisition via DHCP ([ENABLE]: Automatic acquisition is used/[DISABLE]: Automatic acquisition is not used) (Factory setting: [ENABLE]) [IP ADDRESS]: IP address of the camera (Factory setting: [192.168.0.1]). [SUBNET MASK]: Subnet mask (Factory setting: [255.255.255.0]) [DEFAULT GATEWAY]: Default gateway (Factory setting: [192.168.0.254]) [PRIMARY DNS]: Primary DNS server setting (Factory setting: [0.0.0.0]) (When [DHCP] is set to [ENABLE] and can be acquired from the DNS server, the DNS server value which is acquired externally is overwritten. When the value is [0.0.0.0], the server is not set.) [SECONDARY DNS]: Secondary DNS server setting (Factory setting: [0.0.0.0]) (When [DHCP] is set to [ENABLE] and can be acquired from the DNS server, the DNS server value which is acquired externally is overwritten. When the value is [0.0.0.0], the server is not set.) [DHCP SERVER]: Setting whether to use the DHCP SERVER function ([ENABLE]: Use the DHCP SERVER function/[DISABLE]: Does not use the DHCP SERVER function) (Factory setting: [ENABLE]) (cannot be set) 3 Select [WLAN] in main menu → [NETWORK SETUP] → [NETWORK SEL]. If the setting is changed, the camera will restart as necessary. 4 Enter information on the wireless access point to connect to. 1) Select [SELECT] in the main menu → [NETWORK SETUP] → [WIRELESS PROPERTY] → [SSID INPUT MODE]. When [SSID] is selected and the button is pressed, the SSID connection destination list screen (page 184) is displayed. 2) Select the SSID of the connection destination wireless access point using the control stick, and then press the button. ffYou can delete the selected SSID from the connection history by selecting SSID and pressing the button while the is pressed. ffYou can clear all the SSID connection history by pressing the button while pressing the button. 3) Enter the password of the wireless access point to connect to the camera's [ENCRYPT KEY]. 5 Check the network connection. When the setting is completed, confirm that network connection between the camera and the wireless access point is made properly. When network connection is made properly, the network status icon at the upper right of the thumbnail screen changes in yellow, and applications (P2 Browser, FTP client function) which require a network connection can be used. - 183 -