Panasonic microP2 Handheld AVC-ULTRA HD Camcorder Operating Instructions Basic - Page 157

Chapter 7 Display - Screen status display 26 Focus control information display Displays the focus control information with [99] to [00]. [AF] is indicated for auto focus, and [MF] is indicated for manual focus. Also, when [MF ASSIST] is set to [ON] in the main menu → [SW MODE] while in manual focus mode, [MA] is indicated. [95] (distance to the subject: infinity) to [00] (distance to the subject: approx. 5 cm) Depending on the zoom position, the subject may not be within the macro range. Also, depending on the zoom position, the lowest value of the macro range may vary. The display unit can be changed to feet or meters from the main menu → [DISPLAY SETUP] → [ZOOM/FOCUS]. While macro shooting is performed, [AF] or [MF] will be displayed in black and white reversal. 27 Macro display Displayed when you have enabled the macro focus function using the button. 28 Recommended ND filter display Displays the ND filter recommended for the current shooting conditions. 29 Camera warning, notification display area (pages 203, 158) 30 Area frame display Displayed when the control stick is pressed when the function is assigned in the main menu → [SW MODE] → [AREA MODE]. 31 Area display Displayed when in area mode. 32 Flash band compensation function display Displayed when the flash band compensation function is activated. 33 Dynamic range stretcher function display Displayed when the dynamic range stretcher function is working. 34 Scene file name display Indicates the scene file name [F1:] to [F6:]. 35 Image stabilization display Displayed when the button is pressed and the image stabilizer mode has been set. 36 Battery charge level indicator As the battery level decreases, the indication changes → → → → → . When the battery runs out, ( ) flashes. (When the camera is running on the AC adaptor, is displayed.) The battery charge level may not be indicated correctly in a place where the temperature is extremely low or high, or when the camera has not been used for a long period of time. To display the remaining battery level correctly, fully charge the battery, use the camera until the battery runs out, and then charge again. (Even after performing the procedure, the remaining battery may not be indicated correctly if the battery is used under extremely low or high temperature for a long period of time or if the battery has been repeatedly recharged.) Note that the time in the battery charge level indicator is an approximate estimate as it changes according to the conditions of use. 37 P2 card remaining free space ff : This is the slot No. This is displayed in black and white inversion when the slot No. is recording destination. It flashes while the card is being recognized. ff[***min]: Displays the remaining space on the media in each slot. During a near end, it flashes. ff(No display): Not displayed when a card is not inserted. ff[END]: Displayed when there is no space remaining on each card. ff[WP]: Displayed when the P2 card is write-protected. ff[ERR]: Displayed in case of format errors or authentication errors. ff[LOOP ***min]: Displayed when the loop recording mode is set. During the mode check, the second line displays the standard recording time of loop recording. [LOOP] flashes when loop recording is not possible, for example, when there is no more space remaining on the microP2 memory card. 38 Recording media display Among P2 and microP2 memory card slots, displays the slot that can perform recording and playback operations set in the main menu → [RECORDING SETUP] → [REC MEDIA]. ff[mP2]: microP2 memory card slot ff[P2]: P2 memory card slot 39 Simultaneous recording mode display, background recording mode display ff[SIMUL]: Displayed when the simultaneous recording is set. When the simultaneous recording cannot be performed, [SIMUL] indication is displayed with a diagonal line. ff[BACKGR]: Displayed when the camera is in the background recording mode and background recording is being performed on slot 2. When background recording has not started on slot 2, the [BACKGR] indication is displayed with a diagonal line. 40 High-sensitivity mode display Displayed when [HIGH SENS.] is set in the main menu → [SYSTEM MODE] → [SHOOTING MODE]. 41 One clip recording mode status display ff[1‑CLIP]: The status where a new clip is to be recorded in one-clip recording ff[1*CLIP]: The status where recording can be performed by combining to the previous clip in one-clip recording 42 Recording/playback operation status display ff[REC]*1: Recording ff[PAUSE]: Recording standby ff[&]: Playback pause ff[=]: Playback ff Frame-by-frame playback (frame-by-frame rewind) ff[)] ([%]): Fast-forwarding/fast-forward playback (fast-reversing/fast-reverse playback) ff[CLIP&=] ([CLIP~&]): Clip forwarding (clip rewinding), cueing up by clips - 157 -