Samsung SRD-470D User Manual - Page 46

Remote Devices, POS Devices

Get Samsung SRD-470D PDF manuals and user guides View all Samsung SRD-470D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

using the DVR • Duration : Sets the alarm duration for the alarm signal and beep sound. - If was selected, a beep will sound. - If was selected, both beep sound and alarm signal through rear side ports will output. M  status means that the HDD is operating but it has problems that require technical examination. ( ) appears on the Live screen.  status means that the HDD has defect and requires immediate replacement. ( ) appears on the Live screen. 4. When the HDD Alarm setup is done, press . Remote Devices You can set the RS-485 communication for use of PTZ Camera and system keyboard with the DVR. Using the mouse may help make setup easier. 1. Use the up/down buttons () in window to move to , and press [ENTER] button. 2. Use direction buttons to move to the desired item, and press [ENTER] button. 3. Set the values of each communication setup of the remote device. Remote Device Baudrate Parity 9600  None  Data 8  Stop Bit Transfer type 1  Half Duplex System Keyboard OFF Remote Control ON ID 01 ID 00 • Baudrate : Baud rate settings of the DVR, PTZ camera and system keyboard should be matched for proper operations. 4. Make sure to match IDs of the DVR, System Keyboard and Remote Control, and press . OK Cancel M  For changing the remote control's ID, refer to "Changing the Remote Control ID". (Page 12) POS Devices You can set properties of POS devices connected to the DVR. A POS device connection requires channel, preset, and Port/Ethernet settings. Using the mouse may help make setup easier. 1. Use the up/down buttons () in window to move to , and press [ENTER] button. 2. Use direction buttons to move to a desired item, and set the value. • POS USE : When selected , DVR and POS will be connected. POS Device POS USE POS CH 1 None 2 None 3 None 4 None J  If you change settings for the device and press while the is not checked, the changes for POS device will not be saved. Preset  No preset No preset No preset No preset OK Cancel POS Device Setup Port/Ethernet None None None None 46_ using the DVR

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
46_
using the DVR
using the DVR
•
Duration : Sets the alarm duration for the alarm signal and beep sound.
- If <
BEEP
> was selected, a beep will sound.
- If <
All
> was selected, both beep sound and alarm signal through rear side ports will output.
M
<
Check
> status means that the HDD is operating but it has problems that require technical examination.
(
) appears on the Live screen.
<
Replace
> status means that the HDD has defect and requires immediate replacement.
(
) appears on the Live screen.
4.
When the HDD Alarm setup is done, press <
OK
>.
Remote Devices
You can set the RS-485 communication for use of PTZ Camera and system keyboard with the DVR.
Using the mouse may help make setup easier.
1.
Use the up/down buttons (
±²
) in <
Device
> window to
move to <
Remote Device
>, and press [
ENTER
] button.
2.
Use direction buttons (
±²◄ ►
) to move to the desired
item, and press [
ENTER
] button.
3.
Set the values of each communication setup of the remote
device.
•
Baudrate : Baud rate settings of the DVR, PTZ camera and
system keyboard should be matched for proper operations.
4.
Make sure to match IDs of the DVR, System Keyboard
and Remote Control, and press <
OK
>.
M
For changing the remote control’s ID, refer to “
Changing the Remote Control ID
”. (Page 12)
POS Devices
You can set properties of POS devices connected to the DVR.
A POS device connection requires channel, preset, and Port/Ethernet settings.
Using the mouse may help make setup easier.
1.
Use the up/down buttons (
±²
) in <
Device
> window to
move to <
POS Device
>, and press [
ENTER
] button.
2.
Use direction buttons (
±²◄ ►
) to move to a desired
item, and set the value.
•
POS USE : When selected <
POS USE
>, DVR and POS will
be connected.
J
If you change settings for the device and press <
OK
> while
the <
POS USE
> is not checked, the changes for POS device
will not be saved.
System Keyboard
OFF
ID
01
Remote Control
ON
ID
00
Baudrate
Parity
Data
Stop Bit
Transfer type
9600
None
8
1
Half Duplex
Remote Device
OK
Cancel
POS USE
POS
CH
Preset
Port/Ethernet
1
None
No preset
None
2
None
No preset
None
3
None
No preset
None
4
None
No preset
None
POS Device
OK
Cancel
POS Device Setup