Sharp DX-B352P DX-B352P User Manual - Page 20

Non-printing Area

Get Sharp DX-B352P PDF manuals and user guides View all Sharp DX-B352P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Note: • The printer tray is designed with the "paper type dial" for commonly used paper size, which can be adjusted as required. When the paper type used for printing is different from that the dial sets, the LCD display of the printer will show "Optional tray I, PaperSize Mismat." indicating an error, then it is necessary to reset the dial to eliminate the error. • For those paper types that are not shown on the dial, please set up the paper size through the control panel. 4. Raise the output tray to avoid the printed paper from slipping and falling. Note: • If the paper loaded into the optional tray at one time exceed 550 pages (21 lb. bond), paper will jam or cannot be fed in. • If printing only the single side, please make the side to be printed (the blank side) down. • For installation of the optional tray, please refer to the Installation Guide attached with the optional tray. 2.3. Non-printing Area The shaded section indicates the non-printing area. Usage Print Paper Size A4 Letter Top and Bottom Margins (A) 5 mm (0.197 in) 5 mm (0.197 in) Left and Right Margins (B) 5 mm (0.197 in) 5 mm (0.197 in) Note: •The above margin settings only correspond to PCL6. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
12
Note:
•
The printer tray is designed with the "paper type dial" for commonly used paper
size, which can be adjusted as required. When the paper type used for printing
is different from that the dial sets, the LCD display of the printer will show
"Optional tray I, PaperSize Mismat." indicating an error, then it is necessary to
reset the dial to eliminate the error.
•
For those paper types that are not shown on the dial, please set up the paper
size through the control panel.
4.
Raise the output tray to avoid the printed paper from slipping and falling.
Note:
• If the paper loaded into the optional tray
at one time exceed 550 pages
(21 lb. bond), paper will jam or cannot be fed in.
•
If printing only the single side, please make the side to be printed (the blank
side) down.
•
For installation of the optional tray, please refer to the Installation Guide
attached with the optional tray.
2.3. Non-printing Area
The shaded section indicates the non-printing area.
Usage
Paper Size
Top and Bottom
Left and Right
Note: •The above margin settings only correspond to PCL6.
Margins (A)
Margins (B)
A4
Print
Letter
5 mm (0.197 in)
5 mm (0.197 in)
5 mm (0.197 in)
5 mm (0.197 in)