Sharp DX-B352P DX-B352P User Manual - Page 5

Economic Developme

Get Sharp DX-B352P PDF manuals and user guides View all Sharp DX-B352P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

22. This is a low-voltage device. When using the device below its specified voltage, if the toner comes off the printed contents, or the equipment starts up slowly, please refer to the product precautions or call SHARP Service Center. 23. This product is sold as a complete machine. The consumers can go to SHARP Service Center to purchase parts they need. If the product sold is inconsistent with the package list, please go to the specified Service Center to solve the problem. 24. Install this product in a place where the temperature is between 50 and 90° F and the relative humidity between 20% and 80%. 25. For security and other reasons, the printer may switch to intermittent printing after a certain amount of continuous printing. 26. This device contains license-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. 27. This equipment complies with IC RSS-102/FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 8 inches between the radiator and your body. 28. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. 29. Changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 30. Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits. 31. Please keep this User Guide properly. IV

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
IV
22. This is a low-voltage device. When using the device below its specified voltage, if the toner
comes off the printed contents, or the equipment starts up slowly, please refer to the product
precautions or call SHARP Service Center.
23. This product is sold as a complete machine. The consumers can go to SHARP Service Center
to purchase parts they need. If the product sold is inconsistent with the package list, please go
to the specified Service Center to solve the problem.
24. Install this product in a place where the temperature is between 50 and 90° F and the relative
humidity between 20% and 80%.
25. For security and other reasons, the printer may switch to intermittent printing after a certain
amount of continuous printing.
26. This device contains license-exempt transmitter(s) that comply with Innovation, Science and
Economic Developme
nt Canada’s licens
e-exempt RSS(s). Operation is subject to the following
two conditions:
1.
This device may not cause interference.
2.
This device must accept any interference, including interference that may cause
undesired operation of the device.
27. This equipment complies with IC RSS-102/FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter. This equipment should be installed and operated with
minimum distance 8 inches between the radiator and your body.
28. Warning: changes or
modifications
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
29. Changes or modification not expressly approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
30. Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.
31. Please keep this User Guide properly.