TEAC w-865r Owners Manual - Page 13

Continuous Playback, Blank Scan

Get TEAC w-865r PDF manuals and user guides View all TEAC w-865r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

ENGLISH Continuous Playback 2 1 4 4 1 Blank Scan 3 Continuous playback can be performed between TAPE I and TAPE II. When one tape is played back to the end, the other tape automatically starts playback, in a relay fashion. 1 Load pre-recorded tapes into the TAPE I and TAPE II compartments. 2 Set the Dolby NR switch. Always set the Dolby NR switch to the same position that was used for recording. 3 Set the REV MODE switch to the p (CONT PLAY) position. The Blank Scan function detects 10 seconds or more of blank and skips over it. To activate this function, press the BLANK SCAN button followed by the desired play button (h or y). < The BLANK SCAN indicator lights when this function is activated. < To disable this function, press the BLANK SCAN button again. The indicator turns off. < Very quiet passages in music are likely to be identified as blanks. If you are worried about this, switch off Blank Scan. 4 Press the play button (h or y) of the deck you want to start first. You can start continuous playback from either TAPE I or TAPE II. Playback cycles through four tape sides as follows: TAPE I TAPE II Side "A" w Side "B" 2 x Side "B" s Side "A" Playback will automatically stop when both sides of both tapes have been played back 5 times continuously. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
ENGLISH
13
Continuous Playback
3
4
1
1
4
2
Continuous playback can be performed between TAPE I and
TAPE II. When one tape is played back to the end, the other tape
automatically starts playback, in a relay fashion.
Load pre-recorded tapes into the TAPE I and TAPE II
compartments.
Set the Dolby NR switch.
Always set the Dolby NR switch to the same position that was
used for recording.
Set the REV MODE switch to the
p
(CONT PLAY)
position.
Press the play button (
h
or
y
) of the deck you want to
start first.
You can start continuous playback from either TAPE I or
TAPE II.
Playback cycles through four tape sides as follows:
Playback will automatically stop when both sides of both
tapes have been played back 5 times continuously.
TAPE I
Side “A”
w
Side “B”
2
x
TAPE II
Side “B”
s
Side “A”
4
3
2
1
Blank Scan
The Blank Scan function detects 10 seconds or more of blank
and skips over it.
To activate this function, press the BLANK SCAN button followed
by the desired play button (
h
or
y
).
<
The BLANK SCAN indicator lights when this function is
activated.
<
To disable this function, press the BLANK SCAN button again.
The indicator turns off.
<
Very quiet passages in music are likely to be identified as
blanks. If you are worried about this, switch off Blank Scan.