Texas Instruments TINSPIRE Software Installation Guidebook - Page 32

Deployment, Activation, ACTIVATION_TIME_LIMIT=600

Get Texas Instruments TINSPIRE PDF manuals and user guides View all Texas Instruments TINSPIRE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

 ACTIVATION_TIME_LIMIT #Configuration item that sets a fixed amount of time (seconds) to obtain random value when 3 attempt silent activation. Default value is set to 10 minutes. #Accepted values: seconds ACTIVATION_TIME_LIMIT=600 License types: Volume and Concurrent Comment: This field specifies the wait time between activation retries. The system will automatically try to activate up to three times. This value provides way to determine how many seconds to wait before retrying the activation. Deployment There are many deployment packages you can use to distribute the software. Texas Instruments does not make any recommendations or endorse any particular brand or describe steps for using these tools. Please see your deployment tool's instructions for more information. If you experience any problems when deploying TI software, contact the Software Service Center at education.ti.com/go/softwarecenter or 1-800-TI-CARES. Note: If you did not choose SILENT=YES in the setup.ini, the user will see the same install screens as when installing a single license user. Also, the license information will not be pulled from the setup.ini file. Activation Activation either occurs automatically after deployment or when the user runs the client depending on the setting of 'Activate' in the setup.ini. If you set Silent=Yes in the setup.ini, the user will not see any install screens or questions when they launch the software for the first time. If Silent was set to NO, the user will see the same screens as in the basic install. If the license number was entered in the setup.ini and located in the same directory as the client application, the user will not be prompted to enter the license. Note: If you specified activation to occur at deployment but you have individual machines that failed because they were not connected to the Internet, you have to run a basic install on these machines once they are connected. If you have a machine that cannot be connected to the Internet for activation, see Web Portal Activation. 28 Installing and Activating TI Software

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
28
Installing and Activating TI Software
ACTIVATION_TIME_LIMIT
Deployment
There are many deployment packages you can use to distribute the
software. Texas Instruments does not make any recommendations or
endorse any particular brand or describe steps for using these tools.
Please see your deployment tool’s instructions for more information.
If you experience any problems when deploying TI software, contact the
Software Service Center at education.ti.com/go/softwarecenter or
1-800-TI-CARES.
Note:
If you did not choose SILENT=YES in the setup.ini, the user will see
the same install screens as when installing a single license user. Also, the
license information will not be pulled from the setup.ini file.
Activation
Activation either occurs automatically after deployment or when the user
runs the client depending on the setting of ’Activate’ in the setup.ini.
If you set Silent=Yes in the setup.ini, the user will not see any install
screens or questions when they launch the software for the first time. If
Silent was set to NO, the user will see the same screens as in the basic
install.
If the license number was entered in the setup.ini and located in the
same directory as the client application, the user will not be prompted to
enter the license.
Note:
If you specified activation to occur at deployment but you have
individual machines that failed because they were not connected to the
Internet, you have to run a basic install on these machines once they are
connected.
If you have a machine that cannot be connected to the Internet for
activation, see
Web Portal Activation
.
#Configuration item that sets a fixed amount of time (seconds) to obtain
random value when 3 attempt silent activation. Default value is set to 10
minutes.
#Accepted values: seconds
ACTIVATION_TIME_LIMIT=600
------------------------------------------
License types:
Volume
and Concurrent
Comment:
This field specifies the wait time between activation retries.
The system will automatically try to activate up to three times. This
value provides way to determine how many seconds to wait before
retrying the activation.