Toshiba P47LSB User Manual - Page 15

Selection Of The Signals, Function Of Power Panel, Power Switch And Power Indicator

Get Toshiba P47LSB PDF manuals and user guides View all Toshiba P47LSB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

SELECTION of the SIGNALS Video input VIDEO-1 VIDEO-2 VIDEO-3 Composite Video signal, Y/C (S-VIDEO) Y-Pb-Pr(Y-Cb-Cr) US-Pin (RCA) S connector YUV mini-DIN NTSC/PAL NTSC/PAL NTSC/PAL/up to 480p Note: Y-Pb-Pr (Y-Cb-Cr) terminal can accept up to 720p signal. Higher resolution signals are Supplied through RGB terminal. RGB input RGB-1 Analog RGB (PC signal) D-sub HD 15-pin DIGITAL RGB Digital DVI-D input (DVI-D signal input is for PC only, HDCP: not compatible) RGB analog signal/Y-Cb-Cr signal RGB digital signal for PC HD-SDI input HD-SDI Digital High Definition Bit stream signal BNC connector FUNCTION OF POWER PANEL No. Name Function Remarks 1 Power Switch Turn ON and OFF main power ON/OFF 2 AC Inlet AC 100-240V, 50/60Hz input 3P plug POWER SWITCH AND POWER INDICATOR AC power source is turned-on/off with the Main Power Switch. When the Power Switch is turned-on, the Power Lamp Indicator lights in green and the unit enters active state. It takes several seconds typically till an image is shown after Power Switch is turned-on. In the active state, it is possible to power on/off with an external controller or remote control. When power is turned-off with an external controller or remote control, the Power Indicator light will change to yellow and the Display unit enters standby state. RS232C-RS485 connection hint Interval from turn-off to turn-on should be more than 5 seconds. Power lamp indicates green at Power On, No-signal and sleep are orange, stand-by is Yellow. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
15
SELECTION of the SIGNALS
Video input
VIDEO-1 Composite Video signal, US-Pin (RCA) NTSC/PAL
VIDEO-2 Y/C (S-VIDEO)
S connector NTSC/PAL
VIDEO-3 Y-Pb-Pr(Y-Cb-Cr) YUV mini-DIN NTSC/PAL/up to 480p
Note: Y-Pb-Pr (Y-Cb-Cr) terminal can accept up to 720p signal. Higher resolution signals are
Supplied through RGB terminal.
RGB input
RGB-1 Analog RGB (PC signal) D-sub HD 15-pin RGB analog signal/Y-Cb-Cr signal
DIGITAL RGB Digital DVI-D input RGB digital signal for PC
(DVI-D signal input is for PC only, HDCP: not compatible)
HD-SDI input
HD-SDI Digital High Definition Bit stream signal BNC connector
FUNCTION OF POWER PANEL
No. Name
Function
Remarks
1
Power Switch
Turn ON and OFF main power
ON/OFF
2
AC Inlet AC 100-240V, 50/60Hz input
3P plug
POWER SWITCH AND POWER INDICATOR
AC power source is turned-on/off with the Main Power Switch.
When the Power Switch is turned-on, the Power Lamp Indicator
lights in green and the unit enters active state. It takes several
seconds typically till an image is shown after Power Switch is
turned-on.
In the active state, it is possible to power on/off with an external
controller or remote control. When power is turned-off with an
external controller or remote control, the Power Indicator light will
change to yellow and the Display unit enters standby state.
RS232C-RS485 connection hint
Interval from turn-off to turn-on
should be more than 5 seconds.
Power lamp indicates green at
Power On, No-signal and sleep
are orange, stand-by is Yellow.