Toshiba P47LSB User Manual - Page 37

OFF 4 Key Switch Mode ON OFF 5 Video AGC Mode ON OFF 7 PIP Mode ON OFF 8 DPMS Selection ON / OFF ON OFF 9 Display Firmware Version and Date A Display Elapsed Time 02h, (ID), VN0, 03h 02h, (ID), VN4, 03h 02h, (ID), VN1, 03h 02h, (ID), VN0, 03h 02h, (ID), VN5, 03h 02h, (ID), VN1, 03h 02h, (ID), VN0, 03h 02h, (ID), VN7, 03h 02h, (ID), VN1, 03h 02h, (ID), VN0, 03h 02h, (ID), VN8, 03h 02h, (ID), VN1, 03h 02h, (ID), VN0, 03h 02h, (ID), VNA, 03h 02h, (ID), VNB, 03h 02 (ID) 56 4E 30 03 02 (ID) 56 4E 34 03 02 (ID) 56 4E 31 03 02 (ID) 56 4E 30 03 02 (ID) 56 4E 35 03 02 (ID) 56 4E 31 03 02 (ID) 56 4E 30 03 02 (ID) 56 4E 37 03 02 (ID) 56 4E 31 03 02 (ID) 56 4E 30 03 02 (ID) 56 4E 38 03 02 (ID) 56 4E 31 03 02 (ID) 56 4E 30 03 02 (ID) 56 4E 41 03 02 (ID) 56 4E 42 03 Table: 6 Commands used in - ID Mode (with Hex codes) Enter Adjust Mode - then ID Mode Function Description ASCII - CMD String ADJ Adjust Mode - to "Back Up" or "Exit" Service 02h, (ID), AJS, 03h ID ALL Enters ID Mode 02h, (ID), IDA, 03h ID Clear Clears ID 02h, (ID), IDC, 03h ID SET Sets ID 02h, (ID), IDS, 03h 0 Inputs a 0 02h, (ID), VN0, 03h 1 Inputs a 1 02h, (ID), VN1, 03h 2 Inputs a 2 02h, (ID), VN2, 03h 3 Inputs a 3 02h, (ID), VN3, 03h 4 Inputs a 4 02h, (ID), VN4, 03h 5 Inputs a 5 02h, (ID), VN5, 03h 6 Inputs a 6 7 Inputs a 7 02h, (ID), VN6, 03h 02h, (ID), VN7, 03h 8 Inputs an 8 9 Inputs a 9 02h, (ID), VN8, 03h 02h, (ID), VN9, 03h A Inputs an A B Inputs a B 02h, (ID), VNA, 03h 02h, (ID), VNB, 03h C Inputs a C D Inputs a D E Inputs an E 02h, (ID), VNC, 03h 02h, (ID), VND, 03h 02h, (ID), VNE, 03h F ID SEL Inputs an F Selects an ID 02h, (ID), VNF, 03h 02h, (ID), IDT, 03h HEX - CMD String 02 (ID) 41 4A 53 03 02 (ID) 49 44 41 03 02 (ID) 49 44 43 03 02 (ID) 49 44 53 03 02 (ID) 56 4E 30 03 02 (ID) 56 4E 31 03 02 (ID) 56 4E 32 03 02 (ID) 56 4E 33 03 02 (ID) 56 4E 34 03 02 (ID) 56 4E 35 03 02 (ID) 56 4E 36 03 02 (ID) 56 4E 37 03 02 (ID) 56 4E 38 03 02 (ID) 56 4E 39 03 02 (ID) 56 4E 41 03 02 (ID) 56 4E 42 03 02 (ID) 56 4E 43 03 02 (ID) 56 4E 44 03 02 (ID) 56 4E 45 03 02 (ID) 56 4E 46 03 02 (ID) 49 44 54 03 Example of commands: To turn ON the display, from Stand-by mode to power on, then 02h, '**' , 'PON' , 03h (sending to all the cubes to turn On) 02 2A 2A 50 4F 4E 03 Pause (more than 100mS of wait time is recommended) 02h, '**' , 'PON' , 03h (this is simply to make sure, sending the same command twice, may not need) ( Stand-by mode: no power to the back light, LCD panel drive signal/voltage ) 37