Yamaha DTX900 Owner's Manual - Page 75

Reference Basic Structure of the DTX900 Reference Song mode Drum Kit mode Click mode Trigger mode Paramater name NoisModDpt NoisModSpd NoisTon On/Off OSCFrqCors OSCFrqFine OutGain OutLvl OutLvl1 OutLvl2 Output OverDr Pan1 Pan2 PanAEGLvl PanAEGType PanDirectn PanDpth PanType PhShiftOfst Pitch1 Pitch2 PMDepth Pre-LPF PreLPFReso PreModHPF Presenc Ratio RelCurv Release RelTime Reso ResoOfst RevDly RevTime RoomSize Rotor/Horn RotorF RotorS Sens S-FTmHorn Descriptions Determines the depth of the noise modulation. Determines the speed of the noise modulation. Determines the characteristics of the noise. Turns the isolator on or off. Determines the frequency for modulating the input wave. Finely determines the frequency for modulating the input wave. Determines the level gain. Determines the output level. Determines the output level for the 1st series. Determines the output level for the 2nd series. Determines the output level. Determines the degree and character of the distortion effect. Determines the pan position for the 1st series. Determines the pan position for the 2nd series. This parameter of the Slice effect determines the minimum level of the AEG applied to the panned sound. This parameter of the Slice effect determines the type of the AEG applied to the panned sound Determines the type of the Auto Pan. Determines the depth of the pan effect. Determines the pan type. Determines the offset value of the phase modulation. Determines the pitch in semitones for the 1st series. Determines the pitch in semitones for the 2nd series. Determines the depth of the pitch modulation. Determines the Cutoff frequency of the Low Pass Filter before the modulation. Determines the Resonance of the Low Pass Filter for the input sound. Determines the Cutoff frequency of the High Pass Filter before the modulation. This guitar amp effect parameter controls the high frequencies. Determines the ratio of the compressor. Determines the release curve of the envelope follower. Determines the amount of time that elapses between the release or end of a sound and the end of the compressor effect. Determines the release time of the envelope follower. Determines the resonance of the filter. Determines the resonance as offset. Determines the delay time from the early reflections until the reverberations. Determines the reverb time. Determines the room capacity. Determines the volume balance of the horn and rotor. Determines the speed of the rotor when the slow/fast switch is set to "fast." Determines the speed of the rotor when the slow/fast switch is set to "slow." [For FLANGER&PHASER effects, TECH effects] Determines the sensitivity of the modulation applied to the input change. [For TOUCH WAH] Determines the sensitivity of the wah filter's change applied to the input change. Determines how long it takes for the rotation speed of the horn to change from the current speed (slow or fast) to another speed (fast or slow) when the rotation speed is switched. Paramater name S-FTmRotor SmplFrqCtr SpcType Speaker Speed SpeedCtrl Spread Stage Thresh Top*3 Type Vowel WallVary Width WordLen Descriptions Determines how long it takes for the rotation speed of the rotor to change from the current speed (slow or fast) to the another speed (fast or slow) when the rotation speed is switched. Controls the sampling frequency. Selects the type of space simulation. Selects the type of speaker simulation. [For FLANGER] Determines the frequency of the LFO wave which controls the cyclic change of the delay modulation. [For PHASER MONO, PHASER STEREO] Determines the frequency of the LFO wave which controls the cyclic change of the phase modulation. [For AUTO WAH] Determines the speed of the LFO. Switches the rotary speed. Determines the spread of the sound. Determines the step number of the phase shifter. Determines the minimum input level at which the effect is applied. Determines the maximum value of the wah filter. [For FLANGER] Determines the type of flanger. [For WAH effects] Determines the type of Wah. [For EARLY REFLECTION] Determines the type of the reflection sound. Selects a vowel type. Determines the wall status of the simulated room. Higher settings produces more diffuse reflections. Determines the width of the simulated room. Determines the resolution of the sound, or how "rough" the sound is. *1 The Bottom parameter is available only when the value is less than that of the Top parameter. *2 The Color parameter may not be effective depending on the values of the Mode and Stage parameters. *3 The Top parameter is available only when the value is more than that of the Bottom parameter. 75 DTX900 Owner's Manual File mode Utility mode Sampling mode Chain mode