Home » 3Com Manuals » Bridges & Routers » 3Com 3C886 » Manual Viewer

3Com 3C886 User Guide - Page 28

Front Panel LED Description, Table 4

UPC - 662705169279

Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

28 CHAPTER 3: HARDWARE DESCRIPTION AND INSTALLATION Front Panel LED Description s TCP/IP software. TCP/IP is provided as part of the Windows 98, 95, NT and Macintosh System 7.6 and later operating systems. For Windows 3.11 users, TCP/IP software is provided on the 3Com Companion Programs CD-ROM. Available storage space on your computer's hard drive is not required because nothing is installed onto your computer as part of the 56K LAN Modem setup procedure. If you would like to copy any programs or documents from the included CD-ROMs, ensure that you have available hard disk space. The front panel provides the following LEDs. Alert PWR AA CD LAN STATUS RD SD OH TX COLL 1 2 3 4 56K LAN Modem 3C886 3 Com Figure 9 56K LAN Modem Front Panel The functions of the front panel LEDs are described in Table 4. These front panel LEDs indicate proper operation and display 10BASE-T and analog port activity status. Table 4 Front Panel LED Indicator Definitions LED Alert PWR AA CD RD SD OH TX Color Amber Green Green Green Green Green Green Green Description Operational Status. Lit during power-on self-diagnostic test or after pressing the reset button. Off indicates the unit has passed the diagnostic test and is working properly. Flashes if one or more of the diagnostics have failed or after the unit is placed in firmware download mode and is awaiting firmware upgrade. Power Indicator. Remains lit as long as power is supplied to the unit. Auto Answer. Indicates the 56K LAN Modem's answer mode. Flashes during an incoming call. Remains lit for the duration of the call. Off when the LAN Modem originates a call. Carrier Detect. Remains lit if the 56K LAN Modem receives a valid data signal (carrier) from a remote modem (such as an ISP), indicating that data transmission is possible. Received Data. Flashes when the LAN Modem receives data from a remote site. Send Data. Flashes when the LAN Modem sends data to a remote site. Off Hook. Remains lit when the modem has gone off hook. Ethernet Transmit Status. Flashes green when data is being transmitted to the Ethernet LAN from the 56K LAN Modem. Off indicates that no data is being transmitted to the Ethernet LAN from the 56K LAN Modem.

Section	Page
Important Safety Information	3
Additional Safety Information	3
Table of Contents	5
About This Guide	11
Introduction	11
How to Use ThisGuide	11
Conventions	11
Year 2000 Compliance	12
Introduction	13
Introduction	13
56K Access	13
Applications	13
Local Networking with Access to the Internet	14
Local Networking with Access to a Remote Office	14
Features	15
Ease of Installation and Use	15
High Performance	15
Connectivity	15
Routing	15
Bandwidth Management	15
Remote Management	15
Protocols	16
Error Control and Data Compression	16
Modulation Schemes	16
Security	16
Upgradability	16
Diagnostics	16
Warranty	17
Support for Internet Applications	17
56K LAN Modem Functionality Description	19
Connection Types	19
56K Technology	19
LAN Side Connection	19
Application Sharing over the LAN	20
WAN Connection	21
One High Speed Connection	21
Sharing the Connection	21
Call Routing Protocol and IP Address Translation	22
Placing a Call to a Previously Defined Destination	22
Call Routing While No Other Calls are Connected	22
Understanding VPNs and PPTP	23
Setting Up the Server Side of the Tunnel	24
Setting Up the Client Side of the Tunnel	24
For Windows Dial-Up Networking Users	24
Establishing a Tunnel via the LAN Modem	24
Hardware Description and Installation	27
Package Contents	27
Before You Install the 56K LAN Modem	27
Front Panel LED Description	28
Back Panel Connector Description	29
Installing the 56K LAN Modem	29
Before You Begin	29
Installing the Analog Cable	30
Connecting to a 10BASE-T Ethernet Port	30
Connecting to Another Ethernet Hub	31
Before You Begin	31
Installing Analog Equipment	32
Installing the Power Cable	32
Setting Up TCP/IP for Windows and Macintosh	35
TCP/IP Setup Using Windows 95 and 98	35
TCP/IP Setup Using Windows NT 4.0	38
TCP/IP Setup Using Mac OS 7.6 or later	41
TCP/IP Setup Using Windows 3.11	42
Setting up TCP/IP using MS_TCP	42
Configuring the 56K LAN Modem	45
Typical Configuration	45
Before You Begin	45
You Should Have This Information	46
Determine Whether You Use Dynamic or Static IP Addresses	46
Setting Up Your Computer If You Have a Static IP Address	47
For Windows 98 and 95 Users	47
For Windows NT 4.0 Users	47
For Macintosh Users	48
For Windows 3.11 Users	48
Configuring the 56K LAN Modem for the Typical Configuration	49
Configuring a Static IP Address on the 56K LAN Modem	52
Configure Additional Parameters	53
56K LAN Modem Main Page	54
Links From the Illustration	54
Links from the Buttons	55
Advanced Configuration	57
Advanced Configuration	57
Setting Up Additional Service Providers	57
ISP Versus Private Network	58
When to Select ISP	58
When to Select Private Network	58
Setting Up a Connection to an ISP	58
Before You Begin	58
Setting Up a Connection to the Internet	59
Setting Up a Connection to a Private Network	62
Before You Begin	62
Setting Up a Connection to a Remote LAN	62
Associating Service Providers with Computers on the LAN	65
Editing Service Provider Profiles	66
Restricting Access to Service Providers	66
Configuring LAN Parameters	67
Understanding LAN Parameters	67
Name	67
IP Address and Subnet Mask	67
Local Domain Name	68
Enable DHCP Server	68
Enable NetBIOS Filtering	68
Configuring the LAN Parameters	68
Configuring Modem Control Parameters	69
Understanding Modem Controls	69
Connection Controls	69
Mode Controls	69
Protocol Controls	69
Changing Modem Controls	70
Changing Data Call Parameters	71
Understanding Data Call Parameters	71
Minimum Call Duration	71
Disconnecting an Automatic Data Call	71
Disconnecting a Manual Data Call	72
Number of Times to Redial for a Manual Call	72
Delay Between Redial Attempts When Placing a Manual Call	72
Configuring the Data Call Parameters	72
Selective Password Protection	72
Changing Your Password	73
What If I Forget My Password?	73
Locking and Unlocking the Configuration	73
Configuring the LAN Modem from a Remote Location	74
Configuring the LAN Modem Remotely via Another LAN Modem	74
Configuring the LAN Modem Remotely via an Analog Modem	74
Placing, Receiving and Disconnecting Calls	77
Placing Calls	77
Placing a Call Automatically	77
Call Routing Among Service Providers	77
Placing a Call Manually	78
Placing a Call Manually to a Temporary Service Provider	78
Receiving Calls	79
Receiving Voice Calls	79
Receiving Data Calls	79
Auto Answer	79
Disconnecting Calls	80
Disconnecting Calls Manually	80
Disconnecting Calls Automatically Using Timers	80
Minimum Call Duration	80
Idle Timeout	80
Using a Connection Script	80
Before You Begin	80
Accessing the Script Configuration Page	81
Creating a Connection Script	82
Connection Script Command Syntax	82
Using the Configuration Buttons	82
Additional Configuration Buttons	84
Troubleshooting and Maintenance	85
Checking the Basics	85
Monitoring LEDs	85
Monitoring the ALERT LED	85
Monitoring the LAN Port Status LEDs	86
Evaluating Symptoms and Solutions	86
Finding More Information	90
Contacting Technical Support	90
Downloading Firmware to Your 56K LAN Modem	90
Resetting the 56K LAN Modem to a Factory Default Setting	90
Resetting the 56K LAN Modem to the Factory Defaults	90
Reviewing Statistics	91
Understanding System Statistics	91
Understanding Current Call Information	91
Understanding Last Call Information	92
Understanding Service Provider Information	93
Networking Primer	95
What is a network?	95
What is a LAN?	95
What is a WAN?	95
How does a LAN connect to a WAN?	96
What is a LAN Modem?	96
What is a POTS connection?	96
How do different devices communicate with each other?	96
What is TCP/IP?	96
What is an IP Address?	96
What is a Subnet Mask?	97
Dynamic and Static IP Addresses	97
What is DHCP?	97
What is DNS?	97
What is NAT?	98
What are numbered and unnumbered links?	98
How is overall throughput determined?	98
What is a modem?	98
What is the difference between analog and digital signals?	98
What is error correction?	98
What is Data Compression?	98
How does 56K technology work?	99
Possible Limitations	99
Using the Custom Web Browser	101
Custom Links	101
Using Favorites	102
Installing the Custom Internet Explorer Browser	102
Installing Future Releases of Internet Explorer	102
Factory Defaults	103
56K LAN Modem Factory Defaults	103
Specifications	105
General Specifications	105
Year 2000 Compliance	105
Glossary	107
3Com Corporation Limited Warranty	113
FCC Class B Statement	114

Match case Limit results 1 per page

HAPTER

3: H

ARDWARE

ESCRIPTION

AND

NSTALLATION

■

TCP/IP software. TCP/IP is provided as part of the Windows 98, 95, NT and

Macintosh System 7.6 and later operating systems. For Windows 3.11 users,

TCP/IP software is provided on the

3Com Companion Programs

CD-ROM.

Available storage space on your computer’s hard drive is not required because

nothing is installed onto your computer as part of the 56K LAN Modem setup

procedure. If you would like to copy any programs or documents from the

included CD-ROMs, ensure that you have available hard disk space.

Front Panel LED

Description

The front panel provides the following LEDs.

Figure 9

56K LAN Modem Front Panel

The functions of the front panel LEDs are described in Table 4. These front panel

LEDs indicate proper operation and display 10BASE-T and analog port activity

status.

Table 4

Front Panel LED Indicator Definitions

LED

Color

Description

Alert

Amber

Operational Status.

Lit during power-on self-diagnostic test or

after pressing the reset button.

Off indicates the unit has passed the diagnostic test and is working

properly.

Flashes if one or more of the diagnostics have failed or after the

unit is placed in firmware download mode and is awaiting

firmware upgrade.

PWR

Green

Power Indicator.

Remains lit as long as power is supplied to the

unit.

Green

Auto Answer.

Indicates the 56K LAN Modem’s answer mode.

Flashes during an incoming call.

Remains lit for the duration of the call.

Off when the LAN Modem originates a call.

Green

Carrier Detect.

Remains lit if the 56K LAN Modem receives a valid

data signal (carrier) from a remote modem (such as an ISP),

indicating that data transmission is possible.

Green

Received Data

Flashes when the LAN Modem receives data from

a remote site.

Green

Send Data

Flashes when the LAN Modem sends data to a remote

site.

Green

Off Hook

. Remains lit when the modem has gone off hook.

Green

Ethernet Transmit Status.

Flashes green when data is being

transmitted to the Ethernet LAN from the 56K LAN Modem

Off indicates that no data is being transmitted to the Ethernet LAN

from the 56K LAN Modem.

Com

RD SD

COLL

Alert

LAN STATUS

PWR

56K LAN Modem

3C886