Acer TravelMate 310 User Guide - Page 61

Operating on Battery Power, Hibernation mode

Get Acer TravelMate 310 PDF manuals and user guides View all Acer TravelMate 310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

310-e.book Page 41 Tuesday, October 27, 1998 5:17 PM Power Management Note: If the computer beeps but does not enter Standby mode after pressing the Standby hot key, it means the operating system will not allow the computer to enter the power saving mode. The following signals indicate that the computer is in Standby mode: u The buzzer beeps u The Standby indicator lights Warning: Unstored data is lost when you turn off the computer power in Standby mode (by holding the power switch for more than 4 seconds) or when the battery is drained. To leave Standby mode and return to normal mode: u Press any key u Move the active pointing device (internal or external, PS/ 2 or serial) u Allow the Resume Timer to be matched u Open the display cover u Receive an incoming PC card modem event when the Resume on Modem Ring is enabled Hibernation mode In Hibernation mode, all power shuts off (the computer does not consume any power). The computer saves all system information onto the hard disk before it enters Hibernation mode. Once you turn on the power, the computer restores this information and resumes where you left off. Chapter 2 Operating on Battery Power 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Power Management
Chapter 2
Operating on Battery Power
41
The following signals indicate that the computer is in
Standby mode:
The buzzer beeps
The Standby indicator lights
To leave Standby mode and return to normal mode:
Press any key
Move the active pointing device (internal or external, PS/
2 or serial)
Allow the Resume Timer to be matched
Open the display cover
Receive an incoming PC card modem event when the
Resume on Modem Ring is enabled
Hibernation mode
In Hibernation mode, all power shuts off (the computer does
not consume any power).
The computer saves all system
information onto the hard disk before it enters Hibernation
mode.
Once you turn on the power, the computer restores
this information and resumes where you left off.
Note:
If the computer beeps but does not enter Standby
mode after pressing the Standby hot key, it means the
operating system will not allow the computer to enter the
power saving mode.
Warning: Unstored data is lost when you turn off the
computer power in Standby mode (by holding the
power switch for more than 4 seconds) or when the
battery is drained.
310-e.book
Page 41
Tuesday, October 27, 1998
5:17 PM