Acer TravelMate 310 User Guide - Page 62

system activity

Get Acer TravelMate 310 PDF manuals and user guides View all Acer TravelMate 310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

310-e.book Page 42 Tuesday, October 27, 1998 5:17 PM Power Management There are two necessary conditions for the computer to enter Hibernation mode: u The Hibernation file created by PHDISK must be present and valid. See "PhDISK" on page 71 u Heuristic Power Management must be set to [ENABLED] In this situation, there are four ways to enter Hibernation mode: u Pressing the Hibernation hot key Fn-F4 u Allowing the Hibernation Timeout to elapse without any system activity u Experiencing a battery low condition for about a minute. With the Battery Low Suspend parameter in Setup set to [ENABLED] u Allowing the operating system power saving modes to invoke it Note: If the computer beeps but does not enter Hibernation mode after pressing the Hibernation hot key, it means the operating system will not allow the computer to enter the power saving mode. To exit Hibernation mode, press the power switch. The computer also resumes from Hibernation mode if the Resume Timer is set and matched. Warning: Do not change any devices (such as add memory or swap hard disks) when the computer is in Hibernation mode. 42 User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Power Management
42
User’s Guide
There are two necessary conditions for the computer to
enter Hibernation mode:
The Hibernation file created by PHDISK must be present
and valid.
See “PhDISK” on page 71
Heuristic Power Management must be set to [ENABLED]
In this situation, there are four ways to enter Hibernation
mode:
Pressing the Hibernation hot key Fn-F4
Allowing the Hibernation Timeout to elapse without any
system activity
Experiencing a battery low condition for about a minute.
With the Battery Low Suspend parameter in Setup set to
[ENABLED]
Allowing the operating system power saving modes to
invoke it
To exit Hibernation mode, press the power switch.
The
computer also resumes from Hibernation mode if the
Resume Timer is set and matched.
Note:
If the computer beeps but does not enter
Hibernation mode after pressing the Hibernation hot key,
it means the operating system will not allow the computer
to enter the power saving mode.
Warning: Do not change any devices (such as add
memory or swap hard disks) when the computer is in
Hibernation mode.
310-e.book
Page 42
Tuesday, October 27, 1998
5:17 PM