Airlink AR570WV2 User Manual

Airlink AR570WV2 Manual

Get Airlink AR570WV2 PDF manuals and user guides View all Airlink AR570WV2 manuals
Add to My Manuals
Save this manual to your list of manuals

Airlink AR570WV2 manual content summary:

  • Airlink AR570WV2 | User Manual - Page 1
    Wireless N 150 Green Router Model # AR570Wv2 User's Manual Ver. 1A
  • Airlink AR570WV2 | User Manual - Page 2
    . This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions in this manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference, in
  • Airlink AR570WV2 | User Manual - Page 3
    FAMILIAR WITH YOUR NEW GREEN ROUTER ...3 CHAPTER 2 CONFIGURE THE ROUTER ...5 2.1 CONNECT THE ROUTER TO YOUR NETWORK...5 2.2 CONFIGURE THE ROUTER WITH EZ SETUP WIZARD 7 2.3 CONFIGURE THE ROUTER WITH WEB CONFIGURATION UTILITY 16 2.4 CONNECT TO ROUTER WIRELESSLY ...24 CHAPTER 3 ADVANCED CONFIGURATION
  • Airlink AR570WV2 | User Manual - Page 4
    Rule...84 3.5 TOOLBOX ...86 3.5.1 View Log...87 3.5.2 Firmware Upgrade...88 3.5.3 Backup Setting...89 3.5.4 Reset to Default...89 3.5.5 Reboot ...90 3.5.6 Miscellaneous...90 CHAPTER 4 STATUS...91 4.1 SYSTEM STATUS...92 4.2 WIRELESS STATUS...92 4.3 STATISTICS INFORMATION ...92 4.4 NAT STATUS ...93
  • Airlink AR570WV2 | User Manual - Page 5
    Information 1.1 Introduction and safety information Congratulations on your purchase of the Airlink101® AR570Wv2 Wireless N 150 Green Router. This Router is recommended to be used with AirLink101® Wireless N 150 products to provide the best performance. The high bandwidth combined with extended
  • Airlink AR570WV2 | User Manual - Page 6
    Before you start using this router, please check if there is anything missing in the package, and contact your dealer of purchase to claim for missing items: 1. Wireless N 150 Green Router with one un-detachable Antenna 2. Power Adapter 3. Setup CD 4. Quick Installation Guide 5. Ethernet Cable 2
  • Airlink AR570WV2 | User Manual - Page 7
    1.3 Familiar with your new Green Router A. Front Panel LED Status WAN LAN 1~4 W.LAN Status Blinking (Green) On (Green) Blinking Off On (Green) Blinking Off On (Green) Blinking Blinking Rapidly Off Description Device is working properly. Network device is connected Data access Not connected
  • Airlink AR570WV2 | User Manual - Page 8
    B. Back Panel Item Name Antennas 1 - 4 WAN RESET PWR Description These antennas are un-detachable 1.8dBi dipole antennas. Local Area Network (LAN) ports 1 to 4. Wide Area Network (WAN / Internet) port. Press this button and hold for 4 seconds to restore factory default settings. Power connector,
  • Airlink AR570WV2 | User Manual - Page 9
    off your computer, DSL/Cable modem, and the router. Step 1 Connect one end of a network cable to the WAN port of the router and connect the other end of the cable to end to one of the LAN ports of the router, as shown in the following figure. (After setup finishes, you can remove the network
  • Airlink AR570WV2 | User Manual - Page 10
    Step 4 Plug the power adapter to the router and connect it to an electrical outlet. Step 5 Power on your computer. Step 6 Check LEDs of the router: make sure Status, WAN, W.LAN, and the LAN port that the computer is connected to are ON. 6
  • Airlink AR570WV2 | User Manual - Page 11
    2.2 Configure the Router with EZ Setup Wizard Step 1 Insert the Setup CD into CD-ROM drive. Step 2 When the autorun menu pops up, click EZ Setup Wizard. Note: If the autorun menu does not show up on your monitor, please go to Computer Æ CDROM drive Æ Wizard, and execute "EZWizard.exe". 7
  • Airlink AR570WV2 | User Manual - Page 12
    Windows 7 and Vista users: An AutoPlay window pops up on screen. Please make sure you give permission to run the setup program by clicking Run Autorun.exe. Step 3 Select your language and click Next. 8
  • Airlink AR570WV2 | User Manual - Page 13
    Step 4 Click on Wizard. Step 5 Please make sure your computer is connected to one of the 4 LAN ports of the router, and your modem is connected to the WAN port of the router. 9
  • Airlink AR570WV2 | User Manual - Page 14
    setting is disabled. It is suggested to select WPA2-PSK for best wireless security. Step 7 Configure the SSID (wireless network name, i.e. Airlink101), Channel, Security and Key. It is suggested to select WPA2-PSK for best wireless security. Enter 8~63 characters into Key box, then click Next. 10
  • Airlink AR570WV2 | User Manual - Page 15
    will detect your WAN settings, or you can select your WAN type manually by checking "Let me select WAN service by myself". Step 9 Enter the settings based on your WAN service type. Cable (Dynamic IP) If you are using cable Internet service, your WAN type is "Dynamic IP". You do not need to configure
  • Airlink AR570WV2 | User Manual - Page 16
    DSL (PPPoE or Dynamic IP) For DSL users, your WAN type is either PPPoE or Dynamic IP. You can try both types and determine which one works for you. 12
  • Airlink AR570WV2 | User Manual - Page 17
    For PPPoE connection, please enter the user name and password provided by your ISP (Internet Service Provider). Note: Depending on the ISP, you may need to include the domain name with your user name. Example: [email protected] Step 10 Verify
  • Airlink AR570WV2 | User Manual - Page 18
    browser and verify if your computer is connected to the Internet. Step 12 After the WAN service test is completed, click Finish. The wizard will open the web configuration page for the router automatically unless you uncheck "Open the default web browser to access the advanced configuration". 14
  • Airlink AR570WV2 | User Manual - Page 19
    You will see the status of the router on the web configuration page brought up by the web browser. Valid numbers should be assigned to IP Address, Subnet Mask and Gateway, instead of all 0's. 15
  • Airlink AR570WV2 | User Manual - Page 20
    is using the Wizard in the Web Configuration Utility. The wizard will guide you setting up the basic settings of this router. You do not need to go through the wizard again if you have finished 2.2 Configure the Router with EZ Setup Wizard. In order to enter the Web Configuration Utility, you need
  • Airlink AR570WV2 | User Manual - Page 21
    Step 3 When you see this following page pops up, you have successfully logged into the router. Select Wizard and click on Enter to start the Setup Wizard. Step 4 Click Next to start the Setup Wizard. 17
  • Airlink AR570WV2 | User Manual - Page 22
    blank. Click Next. Step 6 Select Auto Detecting WAN Type to let the Wizard detect which Internet connection you are using or select Setup WAN Type Manually to select the Internet connection type manually. Click Next. If you select Setup WAN Type Manually, please specify a WAN type you are using. 18
  • Airlink AR570WV2 | User Manual - Page 23
    address from ISP automatically (Dynamic IP Address) or Some ISPs require the use of PPPoE to connect to their services (PPP over Ethernet) depending on the type of modem provided by your ISP (Internet Service Provider). You can try both settings and determine which one works for you. Click Save. 19
  • Airlink AR570WV2 | User Manual - Page 24
    Step 7 Configure the WAN settings according to the WAN type you selected. Dynamic IP Address: Click on Clone MAC. PPP over Ethernet: Enter the Account and Password provided by your ISP. Note: Depending on the ISP, you may need to include the domain name with your user name. Example: username@
  • Airlink AR570WV2 | User Manual - Page 25
    Keep the default SSID (wireless network name: Airlink101) or change it to a desired name, so you can always recognize your wireless network with it, for example 'myHome'. Select a channel number for your wireless network. Click Next. Step 9 Set up Wireless Security for your router. It is recommended
  • Airlink AR570WV2 | User Manual - Page 26
    . WPA2-PSK (AES) is the most secure encryption mode for general users but some old wireless adapters may not support it. Therefore, please make sure all wireless devices on your network support this security type. Step 10 Verify the information you have configured. If everything is correct, click
  • Airlink AR570WV2 | User Manual - Page 27
    Step 11 When you see the below window, your router has been successfully connected to the Internet. Click Finish. Congratulations! Your router configuration has been finished. Please go to 2.4 Connect to the Router Wirelessly. 23
  • Airlink AR570WV2 | User Manual - Page 28
    In this section, you can find the instructions of how to connect to the router wirelessly with your Windows 7 computer. You can also refer to the manual of your wireless adapter on how to connect to the router. Step 1 Click on the wireless icon in the system tray on your desktop. A list of available
  • Airlink AR570WV2 | User Manual - Page 29
    , you do NOT need to configure anything here for you to start using the Internet. In order to enter the Web Configuration Utility of your router, you need to first log into the router from your web browser. Please follow the steps below: Step 1 From the computer that is connected to the
  • Airlink AR570WV2 | User Manual - Page 30
    Step 3 When you see this page pops up, you have successfully logged into the router. Select Advanced Setup and click Enter to access the complete features and settings of this router. 26
  • Airlink AR570WV2 | User Manual - Page 31
    3.1 Basic Setting You can configure LAN, Internet connection type, DHCP, wireless settings and system password for the router in this page. 27
  • Airlink AR570WV2 | User Manual - Page 32
    WAN (Wide Area Network, i.e. Internet) connection type you configured for the router. Click "Change" to modify. Please see Section 3.1.1.1. If you are not by hosts and adjacent routers on IP networks to establish multicast group memberships. Please find detailed instructions in Section 3.1.1.2. 28
  • Airlink AR570WV2 | User Manual - Page 33
    , you can call your ISP to confirm which WAN type you are using. E. PPTP: Some ISPs require the use of PPTP to connect to their services. F. L2TP: Some ISPs require the use of L2TP to connect to their services Please see the following instructions for settings of each WAN type: 29
  • Airlink AR570WV2 | User Manual - Page 34
    A) Static IP Address Enter the WAN IP address, WAN Subnet Mask, WAN Gateway, Primary DNS , and Secondary DNS addresses provided by your ISP. After you've finished all settings, click Save to save the settings and click Reboot. The change will take effect after rebooting the router. 30
  • Airlink AR570WV2 | User Manual - Page 35
    B) Dynamic IP Address Parameter Host Name WAN's MAC Address Renew IP Forever Description Please input the host name of your router; this is optional and only required if your service provider asks you to do so. Please input MAC address of your computer here if your ISP only permits computer with
  • Airlink AR570WV2 | User Manual - Page 36
    here. (Optional) After you've finished all settings, click Save to save the settings and click Reboot. The change will take effect after rebooting the router. 32
  • Airlink AR570WV2 | User Manual - Page 37
    D) PPP Over Ethernet (PPPoE) Parameter PPPoE Account PPPoE Password Primary DNS Secondary DNS Maximum Idle Time Description Enter the User Name for your DSL account. You can obtain this information from your ISP. Enter the Password for your DSL account. You can obtain this information from your
  • Airlink AR570WV2 | User Manual - Page 38
    will keep the connection to the ISP after the connection is established. Manually: Router will not connect to the ISP until user clicks the Connect button on the Status-page. PPPoE Service Name Enter the DSL service company. This is optional. Assigned IP Address Input the IP address you wish
  • Airlink AR570WV2 | User Manual - Page 39
    IP Address My Subnet Mask Gateway IP Server IP Address/Name PPTP Account Description Select the type of how you obtain IP address from your service provider here: Static IP Address or Dynamic IP Address. Enter the IP address assigned by your ISP if you select Static IP Address. Enter the
  • Airlink AR570WV2 | User Manual - Page 40
    will connect to the ISP when its clients send outgoing packets. Auto Reconnect (Always-on): Router will keep the connection to the ISP after the connection is established. Manually: Router will not connect to the ISP until user clicks the Connect button on the Status-page. Maximum Transmission
  • Airlink AR570WV2 | User Manual - Page 41
    Subnet Mask WAN Gateway IP Server IP Address/Name L2TP Account L2TP Password Description Select the type of how you obtain IP address from your service provider here: Static IP Address or Dynamic IP Address. Enter the IP address assigned by your ISP if you select Static IP Address. Enter the
  • Airlink AR570WV2 | User Manual - Page 42
    will connect to the ISP when its clients send outgoing packets. Auto Reconnect (Always-on): Router will keep the connection to the ISP after the connection is established. Manually: Router will not connect to the ISP until user clicks the Connect button on the Status-page. Maximum Transmission
  • Airlink AR570WV2 | User Manual - Page 43
    3.1.2 DHCP Server This page allows you to configure the DHCP settings for your router. Press button "More>>" for more options. Parameter DHCP Server Lease Time Description Select to Disable or Enable the DHCP server. This is DHCP dynamic IP
  • Airlink AR570WV2 | User Manual - Page 44
    Server. This is optional. This feature allows you to assign a WINS Server. This is optional. Gateway address can be the IP address of an alternate Router. Click Clients List to view DHCP clients. Click Save to save the settings you made. 40
  • Airlink AR570WV2 | User Manual - Page 45
    set parameters that are used for wireless clients to connect to this router. The parameters include SSID, Channel Number, Encryption, etc. Parameters Default Wireless Radio Enable Wireless Off Schedule# Disable Network ID (SSID) Airlink101 Wireless Mode 11b/g/n mixed Description Enable or
  • Airlink AR570WV2 | User Manual - Page 46
    4GHz band, allows 802.11b, 802.11g, and 802.11n wireless network clients to connect to this router (maximum transfer rate 11Mbps for 802.11b clients, maximum 54Mbps . Please see below instructions for each Security type for more details. Please see 3.1.3.3 for Wireless Client List information. 42
  • Airlink AR570WV2 | User Manual - Page 47
    Configuring Security - WEP Note: IEEE802.11n only supports WPA2-PSK or WPA-PSK AES encryption. If you use WEP as your encryption, wireless data rate will drop to 54Mbps (802.11g standard). Key Mode: WEP: Key 1~4: Select HEX or ASCII. You can select ASCII (alphanumeric format) or Hexadecimal (
  • Airlink AR570WV2 | User Manual - Page 48
    PSK Select either AES or TKIP. It is suggested to select AES if all your wireless devices support this encryption mode. Note: IEEE802.11n only supports AES encryption. If you use TKIP as your encryption, wireless data rate will drop to 54Mbps (802.11g standard). Enter 8~63 characters as the security
  • Airlink AR570WV2 | User Manual - Page 49
    When the 802.1x function is enabled, wireless users must authenticate this router first to use the network service. The most common method of implementing 802.1x is by having a RADIUS Server (contain an authentication database) on your LAN, so the router can work simultaneously with it and get user
  • Airlink AR570WV2 | User Manual - Page 50
    It is suggested to select AES if all your wireless devices support this encryption mode. RADIUS Server IP: The RADIUS server's IP address. RADIUS port: The RADIUS server's service port. RADIUS Shared Key: Key value shared by the RADIUS server and this router. This key value should be consistent with
  • Airlink AR570WV2 | User Manual - Page 51
    the WDS feature, the Wireless LAN coverage can be easily extended. Note: WDS-enabled routers or APs from different manufacturers are not guaranteed to work with AR570Wv2. It is recommended to deploy WDS with solely Airlink101® AR570Wv2. When WDS is enabled, it only supports None and WEP encryption
  • Airlink AR570WV2 | User Manual - Page 52
    as well as an AP that allows wireless client association at the same time. (Note: the data throughput is halved with Hybrid mode.) Enter the MAC address of other WDS enabled AP/Router into MAC 1 ~ MAC4. This feature allows you to bridge up to 4 AR570Wv2 routers. It is suggested to use "Copy to
  • Airlink AR570WV2 | User Manual - Page 53
    and the router quickly and easily. Please make sure your wireless device supports this feature as well. If not, you will need to set up the wireless security manually and you can skip this section. In the instructions below, we are going to use the AWLL5099 Airlink101® Wireless N 150 USB Ultra
  • Airlink AR570WV2 | User Manual - Page 54
    Step 3 Within the following 1 minute, push the Easy Setup Button on the Router and hold for less than 1 second. The wireless LED will start blinking quickly. Step 4 The Router will now start the handshake with the wireless adapter, which will take about 30 seconds. When you see the window similar to
  • Airlink AR570WV2 | User Manual - Page 55
    To configure the WPSTM settings of the router, go to Advanced > Basic Setting > Wireless, and click on WPS "Enter" button. There are two methods to activate WPSTM with web configuration utility: PIN and PBC. 1) PIN (Personal Identification Number) You
  • Airlink AR570WV2 | User Manual - Page 56
    Trigger button to start WPSTM. 2) PBC (Push Button Configuration) You can choose to press the hardware Easy Setup Button on the front panel of the router, or select Configure Wireless Station, Software button, and click Trigger button to start WPSTM. 52
  • Airlink AR570WV2 | User Manual - Page 57
    , or "Unconfigured" if WPSTM setup fails. Click Save after you've finished all settings. 3.1.3.3 Wireless Client List This table displays the wireless clients that are currently associated to the router. You can click Back to go back to the Wireless page, or click Refresh to refresh the list. 53
  • Airlink AR570WV2 | User Manual - Page 58
    consists of 0 to 9 alphanumeric characters, and is case sensitive Parameters Old Password New Password Reconfirm Description Enter the current password of the router. Enter the new password. Enter the new password again for verification purposes. Note: If you forget your password, you'll have to
  • Airlink AR570WV2 | User Manual - Page 59
    3.2 Forwarding Rules You can configure Virtual Server, Special Application and Miscellaneous settings in this page. 55
  • Airlink AR570WV2 | User Manual - Page 60
    from the Internet, you must set up port forwarding rules on the router in order to direct incoming traffic to the server or IP Camera. Parameter Well known services Server IP Service Ports Protocol Description You can select a pre-defined service from the list of well known services, select a
  • Airlink AR570WV2 | User Manual - Page 61
    rule. Enter a Schedule Rule number to enable the forwarding rule only within the desired time frame. Please refer to 3.4.7 Schedule Rule for detailed setting instructions. You can set 0 to enable the forwarding rule always. If you assign a schedule rule (for example, 9am to 5pm) to ID#1, users are
  • Airlink AR570WV2 | User Manual - Page 62
    Parameter Description Popular applications Trigger Incoming Ports Enable You can select a pre-defined application from the list of Popular applications, and the ID you wish to fill the setting in. Click Copy to and the setting you selected will be filled into the specific ID. Enter an outbound
  • Airlink AR570WV2 | User Manual - Page 63
    try to access is not 21. Check the Enable box to enable UPnP feature. After you enable the UPnP feature, all client systems that support UPnP, like Windows 7, can discover this router automatically. Xbox is a video game console produced by Microsoft Corporation. Check the Enable box to enable Xbox
  • Airlink AR570WV2 | User Manual - Page 64
    3.3 Security Setting You can configure Internet access rules for your local computers based on Packet Filters, Domain Filters, URL Blocking, MAC Access Control and Miscellaneous settings in this page. 60
  • Airlink AR570WV2 | User Manual - Page 65
    or restricting your local network. Example: Computers with IP addresses between 192.168.2.20 to 192.168.2.50 have no restriction on accessing any network services, while other computers are all blocked. Meanwhile, computers with IP addresses between 192.168.2.100 to 192.168.2.199 are allowed to send
  • Airlink AR570WV2 | User Manual - Page 66
    For each rule, you can define: • Source IP address • Destination IP address • Destination port address • Protocol: TCP or UDP or both. Parameters Description Outbound Packet Filter Check/uncheck Enable to enable/disable the Packet Filtering. Outbound Filter applies to all outbound packets but
  • Airlink AR570WV2 | User Manual - Page 67
    Inbound Filter Rule for detailed setting instructions. Set 0 to let the filtering rule always take effect. Click Inbound Filter button to go to Inbound Packet Filter settings. Click Save after you've finished all settings. Click Inbound Filter to configure inbound traffic filters. 63
  • Airlink AR570WV2 | User Manual - Page 68
    /disable Domain Filter. Check/Uncheck Enable box to enable/disable logging DNS Query. Enter a host IP address range that has privilege to access any network service without restriction. For example, From 10 to 20. You can enter a domain suffix of URL to be restricted, for example, ".com" or "xxx.com
  • Airlink AR570WV2 | User Manual - Page 69
    Check Drop or Log or both to determine the actions of router, when user attempts to access the restricted domain. According to the desired time frame. Please refer to 3.4.7 Schedule Rule for detailed setting instructions. Set 0 to let the filtering rule always take effect. Click Save after you
  • Airlink AR570WV2 | User Manual - Page 70
    3.3.3 URL Blocking You can block access to certain websites or web contents from local PCs by entering a full URL address or just keywords. The major difference between "Domain Filter" and "URL Blocking" is that Domain Filter requires user to input a suffix (like .com or .org, etc), while URL
  • Airlink AR570WV2 | User Manual - Page 71
    the desired time frame. Please refer to 3.4.7 Schedule Rule for detailed setting instructions. Set 0 to let the filtering rule always take effect. Click Save to your wireless router. Only those network devices with MAC addresses you specified here are allowed to access your wireless router. You
  • Airlink AR570WV2 | User Manual - Page 72
    only when Enable is checked. Check this box to enable the rule that wireless or wired clients whose MAC addresses are in the table can connect to the router. Choose "allow" or "deny" to determine whether the router allows or denies connection from other clients whose MAC addresses are not in the
  • Airlink AR570WV2 | User Manual - Page 73
    you selected; you do not need to enter it manually. Input the MAC address of your computer / network device. Check this box to allow the wired/wireless client to connect to the router. Check this box to allow the wireless client to associate to the wireless network. You can set up to 32 MAC control
  • Airlink AR570WV2 | User Manual - Page 74
    time-out period to zero to disable this feature. Check this box to enable Discard PING from WAN side. When you enable this feature, your router will not respond to a "ping" request from any host on the WAN side. Stateful Packet Inspection mode is a firewall that keeps track of the state
  • Airlink AR570WV2 | User Manual - Page 75
    DoS Attack Detection VPN PPTP Pass-Through VPN IPSec Pass-Through Check this box to enable the DoS Attack Detection. Router will block the DoS once it is detected. Denial of Service (DoS) is a common attack measure, by transmitting a great amount of data or requests to your Internet IP address and
  • Airlink AR570WV2 | User Manual - Page 76
    3.4 Advanced Setting This page allows you to set up System Time, System Log, Dynamic DNS, QoS Rule, SNMP, Routing, and Schedule Rule. 72
  • Airlink AR570WV2 | User Manual - Page 77
    Synchronize with PC. > Select Set Date and Time using PC's Date and Time 3) Manually configure the time ¾ Select Set Date and Time manually Parameter System Time Sync Now Description Displaying the current system time of router. Click this button to synchronize the system time with the desired 73
  • Airlink AR570WV2 | User Manual - Page 78
    . Select "Set Date and Time using PC's Date and Time", and router will automatically copy the date and time from your PC. Select Year, Month, Day, Hour, Minute, and Second if you wish to set the system date and time manually. Select Enable or Disable for daylight saving according to where you
  • Airlink AR570WV2 | User Manual - Page 79
    enable this function to log all important system events for your router. This page provides two methods to export system logs to to enable Email Alert (send syslog via Email). Email Alert will work only if the router connects to Internet. Click Send Mail Now to email system log to the account you
  • Airlink AR570WV2 | User Manual - Page 80
    Email Addresses Email Subject Username Password Log Type View Log '/'. If you do not specify port number, the default value is 25. For example, "mail.abc.com" or "192.168.1.100/25". Enter the Email addresses of the recipients who will receive these logs. You can assign more than 1 recipient by
  • Airlink AR570WV2 | User Manual - Page 81
    Parameter DDNS Provider Provider Website Host Name Username / E-mail Password / Key Description Select to Disable or Enable DDNS function. A DDNS provider provides service for you to bind your IP (even private IP) with a certain Domain name. Choose a desired provider. Click Provider Website to go
  • Airlink AR570WV2 | User Manual - Page 82
    provides an efficient way for computers on the network to share the Internet bandwidth with a promised quality of Internet service. Without QoS, all computers and devices on the network will compete with one another to get Internet bandwidth, and some applications which require guaranteed bandwidth
  • Airlink AR570WV2 | User Manual - Page 83
    QoS rule. Enter a Schedule Rule number to activate the QoS rule only within the desired time frame. Please refer to 3.4.7 Schedule Rule for detailed setting instructions. Click Save after you've finished all settings. 79
  • Airlink AR570WV2 | User Manual - Page 84
    3.4.5 SNMP Configure the router to allow administrative computers to control it through SNMP(Simple Network Management Protocol). Parameter send SNMP Trap message to. Please select proper SNMP Version that your SNMP Management software supports. Click Save after you've finished all settings. 80
  • Airlink AR570WV2 | User Manual - Page 85
    3.4.6 Routing Routing Table allows you to determine which physical interface address to use for outgoing IP data grams. If you have more than one router and subnet, you will need to enable routing table to allow packets to find proper routing path and allow different subnets to communicate with each
  • Airlink AR570WV2 | User Manual - Page 86
    For Example: AR570Wv2 Configuration on Static Routing Destination Subnet Mask Gateway Hop 192.168.1.0 255.255.255.0 192.168.123.216 1 192.168.0.0 255.255.255.0 192.168.
  • Airlink AR570WV2 | User Manual - Page 87
    portion is the host portion. Enter the gateway IP address. This is the IP address of the gateway device that allows for contact between the Router and the remote network or host. Specify the number of next hop. Check or uncheck Enable box to enable or disable the static routing rule
  • Airlink AR570WV2 | User Manual - Page 88
    the rule from the schedule rule table. Click Add New Rule to add a new rule to the schedule rule table. Please refer to 3.4.7.1 for detailed instructions. Click Save after you've finished all settings. 84
  • Airlink AR570WV2 | User Manual - Page 89
    Rule# System Time Week Day Start Time/End Time (hh:mm) Description Enter a name for the new rule. Displays the current system time of the router for you to verify if this matches the date/time of where you are located. You can refer to 3.4.1 on how to modify the system
  • Airlink AR570WV2 | User Manual - Page 90
    3.5 Toolbox The Toolbox page allows you to view system logs, upgrade firmware, save/reload configuration settings, reset factory default settings, reboot the router, and perform ping test. 86
  • Airlink AR570WV2 | User Manual - Page 91
    3.5.1 View Log You can view, download, and clear the system logs stored in the router here. 87
  • Airlink AR570WV2 | User Manual - Page 92
    Upgrade You can view the current firmware version of router in this page. To upgrade the firmware for the router, you must use a computer that is wired connected to the router. You need to download the firmware from www.airlink101.com and save it to your local hard disk first. You may need to
  • Airlink AR570WV2 | User Manual - Page 93
    Setting and save it as a .bin file. Once you need to restore the settings, please go to Firmware Upgrade page and load the .bin file you've saved. 3.5.4 Reset to Default To restore the router settings to factory default, click Reset to Default, and you will be prompted: Click OK to continue
  • Airlink AR570WV2 | User Manual - Page 94
    3.5.5 Reboot To reboot the router, click Reboot, and you will be prompted: Click OK to continue the MAC address of this device. Enter the MAC address of the device and click Wake Up. The router will send wake-up frame to the target device immediately and the device can be powered up remotely. Enter
  • Airlink AR570WV2 | User Manual - Page 95
    Chapter 4 Status The Status section allows you to monitor the current status of your router. You can use the Status page to monitor: the Internet connection, Wireless, NAT status, and the statistics information of the Router. 91
  • Airlink AR570WV2 | User Manual - Page 96
    from the ISP (Internet Service Provider). And you may go back to Primary Setup page to edit the Internet connection settings by clicking Edit. 4.2 Wireless Status You can view the Wireless LAN status of your router, including SSID (the name of your wireless network), Channel number, Security
  • Airlink AR570WV2 | User Manual - Page 97
    4.4 NAT Status Click NAT Status on the bottom of the Status page to view NAT Status. 93
  • Airlink AR570WV2 | User Manual - Page 98
    4 x 10/100Mbps LAN port • SPI Firewall Antenna type - IP/Service Filter • One 1.8dBi un-detachable dipole - MAC Control antenna - URL H) LAN1~4 Temperature Interface ƒ Reset ƒ Easy Setup Button (WPS TM compatible) ƒ Wireless ON • Operating: 0ºC to 40ºC Humidity • Operating: 10% to 90% Non
  • Airlink AR570WV2 | User Manual - Page 99
    Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Website: www.airlink101.com *Theoretical maximum wireless signal rate derived from IEEE standard 802.11N specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
Wireless N 150 Green Router
Model # AR570Wv2
User’s Manual
Ver. 1A