Alpine HCE-C305R Owners Manual - Page 21

Installing the Switch, Installing the Control Unit

Get Alpine HCE-C305R PDF manuals and user guides View all Alpine HCE-C305R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

4. Installing the Switch 1 Attach the switch@ according to the following illustration. Attach the supplied switch adhesive sheet @ . Peel off the protective sheet, and apply it to the back of the switch, then peel off the other protective sheet and install in the desired location. If necessary, secure the cable with the supplied cord clamps@. • Before attaching the switch, wipe off any dust, oil, etc., on the attaching surface with a suitable cleaning cloth (sold separately). • Attach the switch in a location where driving is not hindered. 5. Installing the Control Unit 1 Attach the control unit® with the Velcro fastener® or self-tapping screw 0. • It is recommended to install the control unit on the rear of the instrument panel, or under a seat. • Attaching with Velcro fastener (1) Attach the Velcro fastener (hard side) ®to the bottom of the control unit®. Velcro fastener • Attach the Velcro fastener in an area on the bottom of the unit undersurface where the label is not attached. (2) Attach the Velcro fastener (soft side) ®to the floor, and secure the control unit®. • When attaching the Velcro fastener (hard side)® to the floor carpet, do so without the Velcro fastener (soft side)® attached. • Attaching with the self-tapping screw (1) Attaching the control unit with the 0 self-tapping screw in a flat location. 20-EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
20-EN
4. Installing the Switch
1
Attach the
switch@
according to the
following illustration.
Attach
the
supplied switch adhesive sheet
@.
Peel
off
the
protective sheet, and apply
it
to
the
back
of
the switch,
then
peel
off
the
other
protective sheet and install in
the
desired location. If necessary, secure
the
cable
with
the
supplied cord
clamps@.
•
Before attaching the switch, wipe
off
any dust, oil,
etc., on the attaching surface with a suitable cleaning
cloth (sold separately).
•
Attach the switch in a location where driving
is
not
hindered.
5. Installing the Control Unit
1
Attach the control
unit®
with the Velcro
fastener®
or self-tapping screw
0.
•
It
is
recommended
to
install the control unit on the
rear
of
the instrument panel, or under a seat.
•
Attaching with Velcro fastener
(1)
Attach
the
Velcro
fastener
(hard
side)
®to
the bottom
of
the control
unit®.
Velcro fastener
•
Attach the Velcro fastener in an area on the bottom
of
the unit undersurface where the label
is
not
attached.
(2) Attach the Velcro fastener (soft side)
®to
the floor, and secure the control
unit®.
•
When
attaching the Velcro fastener (hard
side)®
to
the floor carpet, do
so
without the Velcro fastener
(soft
side)®
attached.
•
Attaching with the self-tapping screw
(1)
Attaching the control unit with the
self-tapping screw
0
in a flat location.