Alpine HCE-C305R Owners Manual - Page 36

Information

Get Alpine HCE-C305R PDF manuals and user guides View all Alpine HCE-C305R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Information Specifications • Camera section Image sensor 1/4 Type Color CMOS Image sensor, aspect ratio 4: 3 Effective Number of Pixels.. 640 (horizontal) x 480 (vertical) approximately 0.3 Megapixels Lens Section Focal length f = 0.82 mm, brightness F = 2.6 Angle of Field Horizontal: 190 °, Vertical: 150 o (Control unit output: 180 °) Automatic Image Adjusting Function Automatic metering adjustment, Automatic white balance adjustment Synchro-System Internal synchronization Resolution (Horizontal)..... 300 TV lines (center area) Illumination Range......... 1.5 to 100,000 lx Operating Temperature Range 22 to+ 158 oF (-30 to +70 °C) Storage Temperature Range 40 to+ 185 oF (-40 to +85 °C) External Dimensions 23.4 x 23.4 x 25.9mm (W X D X H) (15/16"x 15/16"x 1-1/1 6") (excluding cable) Weight 32 g (including cable) • Control unit section Power Requirements....... 14.4 V DC (1 1 to 16 V allowable) Ground Type Negative ground type Output Image Mirror image, CVBS (NTSC Color signal system) Output Drive Capacity . . . . . 75 ohm Operating Temperature Range 4to+140°F (-20 to +60 °C) External Dimensions 176 x 110 x 30 mm (W X D X H) (6-15/16" X 4-5/16" X 1-3/16") Weight 450 g (including cable) In Case of Difficulty • The camera image does not appear. (Images other than that of the camera are normal.) Cause Solution The ignition key is Set the ignition key to ON. set to a position other than ON. No fuse is installed, or Install a fuse, or replace a there is a break in the relevant fuse after checking connection. the cause. The connection is not correctly established. Check whether the connection is correctly established while referring to this owner's manual. The reverse signal line of the connected product is not connected. Connect the reverse signal line while referring to the owner's manual of the connected product. The video connection cable is not connected to the camera input of the connected product. Connect the video connection cable to the camera input while referring to the owner's manual of the connected product. The rear camera image does not display, and the calibration mode appears. The control unit SETUP switch might be ON. Turn the ignition key to OFF and then set the SETUP switch to OFF. Wait for approximately 1 minute and then turn the ignition key to ON again. • The camera image is not normal. (Images other than that of the camera are normal.) Symptom The display screen flickers. The screen is difficult to read. The camera image sways. The camera image is unclear. Cause/Solution If a place illuminated by a fluorescent lamp is captured, the display screen may flicker. This is not a failure. If a dark place or a partially bright light is captured, or if the temperature of the main body of the camera is high, the screen may be difficult to read. This is not a malfunction. Check the installation status, and check screws for looseness. If the camera lens is dirty, wipe the lens softly with a soft cloth moistened with water. 35-EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
Information
Specifications
•
Camera section
Image sensor . . . . . . . . . . . . . .
1/4 Type Color
CMOS
Image sensor, aspect
ratio
4:
3
Effective
Number
of
Pixels..
640 (horizontal) x 480
(vertical) approximately
0.3
Megapixels
Lens
Section
...............
Focal
length f
=
0.82
mm,
brightness F =
2.6
Angle
of
Field
..............
Horizontal: 190
°,
Vertical: 1
50
o
(Control
unit
output:
180
°)
Automatic Image Adjusting
Function. . . . . . . . . . . . . . . . . . .
Automatic metering
adjustment, Automatic
white
balance
adjustment
Synchro-System
............
Internal synchronization
Resolution
(Horizontal)
.....
300 TV lines (center
area)
Illumination
Range
.........
1.5
to
100,000 lx
Operating Temperature
Range . . . . . . . . . . . . . . . . . . . . .
-22
to+
158
oF
(-30
to
+70
°C)
Storage Temperature
Range . . . . . . . . . . . . . . . . . . . . .
-40
to+
185
oF
(-40
to
+85
°C)
External Dimensions . . . . . . .
23.4 x 23.4 x 25.9mm
(W
X
D
X
H)
(15/16"x
15/16"x
1-1/1 6") (excluding
cable)
Weight . . . . . . . . . . . . . . . . . . . .
32
g (including cable)
•
Control unit section
Power
Requirements
.......
14.4 V
DC
(1
1
to
16
V allowable)
Ground
Type
...............
Negative
ground
type
Output
Image
..............
Mirror image,
CVBS
(NTSC
Color signal
system)
Output
Drive Capacity . . . . .
75
ohm
Operating Temperature
Range
.....................
-4to+140°F
(-20
to
+60
°C)
External Dimensions . . . . . . .
176 x 110 x 30
mm
(W
X
D
X
H)
(6-15/16"
X
4-5/16"
X
1-3/16")
Weight . . . . . . . . . . . . . . . . . . . .
450 g (including cable)
In Case
of
Difficulty
• The camera image does not appear. (Images
other than that of the camera
are
normal.)
Cause
Solution
The ignition key
is
Set the ignition key to ON.
set to a position
other
than ON.
No fuse
is
installed,
or
Install a fuse, or replace a
there
is
a break in the
relevant fuse after checking
connection.
the cause.
The
connection
is
not
Check whether the connection
correctly established.
is
correctly established while
referring to this owner's
manual.
The reverse signal
Connect the reverse signal line
line
of
the connected
while referring to the owner's
product
is
not
manual
of
the connected
connected.
product.
The video connection
Connect the video connection
cable is not connected
cable to the camera input
to the camera input
while referring to the owner's
of
the connected
manual
of
the connected
product.
product.
The rear camera
The control unit SETUP
image does not
switch might be ON.
display, and the
Turn the ignition key to OFF
calibration
mode
and then set the SETUP switch
appears.
to
OFF.
Wait for approximately
1
minute and then turn the
ignition key to
ON
again.
• The camera image
is
not normal. (Images other
than that
of
the camera are normal.)
Symptom
Cause/Solution
The display screen
If a place illuminated by a
flickers.
fluorescent lamp
is
captured,
the display screen may flicker.
This
is
not a failure.
The screen
is
difficult
If a dark place
or
a partially
to read.
bright light
is
captured,
or
if
the temperature
of
the main
body
of
the camera
is
high, the
screen may be difficult to read.
This
is
not a malfunction.
The camera image
Check the installation
sways.
status,
and
check screws for
looseness.
The camera image
is
If
the camera lens
is
dirty, wipe
unclear.
the lens softly with a soft cloth
moistened with water.
35-EN