Alpine HCE-C305R Owners Manual - Page 32

Performing Calibration

Get Alpine HCE-C305R PDF manuals and user guides View all Alpine HCE-C305R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Performing Calibration • Measure and input calibration data carefully. Errors can result in image distortion, guideline misplacement, and degradation ofdetection performance. • If the ignition key is turned off during calibration, the settings will not be saved. 1 Set the SETUP switch of the control unit to 0 11 N:' 4 Press VIEW, select 11Change" for (em) or (Inch), and press SET. to execute. 2 Set the ignition key to ACC ON. The camera system starts in calibration mode. 3 Display the camera screen and press VIEW. • Refer to "Turning the Rear Can1era On and Off" (page 14). The Graphic display range adjust screen appears. • Execute calibration at the selected unit. • Select "Change" under ((Language" in the Top menu screen to change the display text language. For operation instructions, refer to the step 19. 5 Press SET. to adjust the display range. Line with which to align the end of the bumper The Top menu screen appears. Adjust so that the bumper appears within the orange adjustment frame. The bumper should take up about 10% of the area inside the frame. • If the bumper takes up too much space or almost does not show at all, adjust the installation angle of the camera to fit within the angle range on page 17. • If the adjustment frame is set to the bottommost position, the area outside the camera range (black circle edge) might be displayed in the bottom portion of the screen. If the area outside the camera range is distracting, set the adjustment frame one level upwards. 6 Press VIEW, select 11Next:' and press SET. to execute. The Input Camera Position screen appears. 31-EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
Performing Calibration
•
Measure and input calibration data carefully.
Errors
can
result
in
image distortion, guideline
misplacement, and degradation
of
detection
performance.
•
If
the ignition key
is
turned
off
during calibration,
the settings will not
be
saved.
1
Set
the
SETUP switch
of
the
control
unit
to
11
0N:'
2
Set
the
ignition key
to
ACC
ON.
The camera system starts in calibration mode.
3
Display
the
camera screen
and
press
VIEW.
• Refer to
"Turning
the Rear Can1era
On
and
Off"
(page 14).
The Top
menu
screen appears.
4
Press VIEW, select
11
Change" for (em)
or
(Inch),
and
press
SET.
to
execute.
The Graphic display range adjust screen
appears.
• Execute calibration at the selected unit.
• Select "Change"
under
((Language" in the
Top
menu
screen to change
the
display text
language. For
operation
instructions, refer
to
the
step
19.
5
Press
SET.
to
adjust
the
display range.
Line with which to align
the end
of
the bumper
Adjust
so
that
the
bumper
appears
within
the
orange
adjustment
frame. The
bumper
should take
up
about
10%
of
the
area
inside
the
frame.
•
If
the
bumper
takes
up
too
much
space
or
almost does
not
show at all, adjust
the
installation angle
of
the
camera to fit within
the
angle range
on
page
17.
•
If
the
adjustment
frame is set to
the
bottommost
position,
the
area outside
the
camera
range (black circle edge)
might
be displayed
in
the
bottom
portion
of
the
screen.
If
the
area outside the camera range
is distracting, set the
adjustment
frame one
level upwards.
6
Press VIEW, select
11
Next:'
and
press
SET.
to
execute.
The
Input
Camera Position screen appears.
31-EN