Asus T2-AH1 T2-AH1 English user manual E2065 - Page 37

Installing an optical drive - barebone

Get Asus T2-AH1 PDF manuals and user guides View all Asus T2-AH1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

2.8 Installing an optical drive The barebone system comes with two 5.25-inch drive bays for two optical drives. • You may install a second optical drive only if you installed a Serial ATA hard disk drive. • Set your second optical drive as Slave device before connecting the IDE cable and power plug. Refer to the optical drive documentation on how to set the drive as a Slave device. To install an optical drive: 1. Place the chassis upright. 2. Locate the front panel cover hooks. 3. To remove the front panel cover from the chassis, press the top hooks downward and the bottom hooks upward to release them from the metal tabs that secure them in place. 4. Detach the front panel cover top hooks. 3 3 1 2 3 3 4 4 5. Slightly push the front panel cover outward until it detaches from the chassis, then set it aside. 5 ASUS T2-AH1 2-17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
2-17
2-17
2-17
2-17
2-17
ASUS T2-AH1
ASUS T2-AH1
ASUS T2-AH1
ASUS T2-AH1
ASUS T2-AH1
2.8
Installing an optical drive
The barebone system comes with two 5.25-inch drive bays for two optical
drives.
To install an optical drive:
1.
Place the chassis upright.
2.
Locate the front panel cover
hooks.
3.
To remove the front panel cover
from the chassis, press the top
hooks downward and the
bottom hooks upward to release
them from the metal tabs that
secure them in place.
4.
Detach the front panel cover
top hooks.
5.
Slightly push the front panel
cover outward until it detaches
from the chassis, then set it
aside.
1
2
3
•
You may install a second optical drive only if you installed a Serial
ATA hard disk drive.
•
Set your second optical drive as Slave device before connecting the
IDE cable and power plug. Refer to the optical drive documentation
on how to set the drive as a Slave device.
3
3
3
5
4
4