Asus T2-AH1 T2-AH1 English user manual E2065 - Page 40

Installing a floppy disk drive

Get Asus T2-AH1 PDF manuals and user guides View all Asus T2-AH1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

2.9 Installing a floppy disk drive The barebone system comes with one 3.25-inch drive bay for a floppy disk drive. To install a floppy disk drive: 1. Remove the front panel cover. For instructions on how to remove the front panel cover, refer to steps 1-5 of section "2.8 Installing an optical drive." 2 2. Carefully insert the floppy disk drive into the floppy drive bay until the screw holes align with the holes on the bay. 3. Secure the floppy disk drive with two screws. 33 4. Connect the floppy disk drive signal cable to the signal connector at the back of the drive. 5. Connect the other end of the signal cable to the floppy disk drive connector (labeled FLOPPY) on the motherboard. See page 4-6 for the connector location. 6. Connect a power cable from the power supply unit to the power connector at the back of the floppy disk drive. See page 2-25 for details on the power supply unit plugs. 6 4 2-20 Chapter 2: Basic installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
2-20
2-20
2-20
2-20
2-20
Chapter 2: Basic installation
Chapter 2: Basic installation
Chapter 2: Basic installation
Chapter 2: Basic installation
Chapter 2: Basic installation
2.9
Installing a floppy disk drive
The barebone system comes with one 3.25-inch drive bay for a floppy disk
drive.
To install a floppy disk drive:
1.
Remove the front panel cover.
For instructions on how to
remove the front panel cover,
refer to steps 1-5 of section
“2.8 Installing an optical
drive.”
2.
Carefully insert the floppy disk
drive into the floppy drive bay
until the screw holes align with
the holes on the bay.
3.
Secure the floppy disk drive with
two screws.
2
3
3
4
6
4.
Connect the floppy disk drive
signal cable to the signal
connector at the back of the
drive.
5.
Connect the other end of the
signal cable to the floppy disk
drive connector (labeled
FLOPPY) on the motherboard.
See page 4-6 for the connector
location.
6.
Connect a power cable from the
power supply unit to the power
connector at the back of the
floppy disk drive. See page 2-25 for
details on the power supply unit plugs.