Brother International BAS-300 Series Programmer Instruction Manual - English - Page 14

Brother International BAS-300 Series Manual

Get Brother International BAS-300 Series PDF manuals and user guides View all Brother International BAS-300 Series manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Os To program a symmetrical mirror image of a pattern design A. Use the key (Mirror key) to program a symmetrical mirror image of a stitch pattern which has already been programmed. Example: Program a symmetrical mirror image of the pattern in the figures below. (1) Press the key. The work clamp will move to the point of origin (X-0; Y-0), the numeral "0" will be indicated on the STEP display; and the command indicator "F" will illuminate. (2) Insert the disk containing the stitch pattern into the disk drive. (3) Press the R/W switch. The data indicator will illuminate and the program data will being read into the memory. 0, (4) If the pattern in section 0 of the figure on the left is the original design, press "001" to program the pattern in section "011" to program the pattern in section 0, and "010" to program the pattern in section O. Operate the numeral keys to indicate the appropriate number on the STEP display. g (5) Press the M key, and then press the key. (6) Press the R/W switch to write the pattern to disk. (Refer to page 24.) Press the key to enter the sewing mode. Note 1 Note 2 When the key is used to compose a symmetrical mirror image, the program will be input with the initial stitch position as the starting point of the entire symmetrical pattern as shown in the figures below. In the event that the mirror image may extend beyond the limits of the work clamp, or if the entire symmetrical pattern is to be moved to the center of the work clamp, etc., press the key after completing the procedure from 1-5 mentioned above. Then, press the direction keys to move the work clamp to the newly-established initial stitch position, and press the key. Thus, the newly-established initial stitch position will be programmed. O -ow - O Origin figure (X-0, Y-0) O Origin figure O o Q "011" - ' L "1- O -010- - 1 io - O 0 -ow- ®0 New position - Initial stitch

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
Os
To
program
a
symmetrical
mirror
image
of
a
pattern
design
A.
Use
the
key
(Mirror
key)
to
program
a
symmetrical
mirror
image
of
a
stitch
pattern
which
has
already
been
programmed.
Example:
Program
a
symmetrical
mirror
image
of
the
pattern
in
the
figures
below.
(1)
Press
the
key.
The
work
clamp
will
move
to
the
point
of
origin
(X-0;
Y-0),
the
numeral
"0"
will
be
indicated
on
the
STEP
display;
and
the
command
indicator
"F"
will
illuminate.
(2)
Insert
the
disk
containing
the
stitch
pattern
into
the
disk
drive.
(3)
Press
the
R/W
switch.
The
data
indicator
will
illuminate
and
the
program
data
will
being
read
into
the
memory.
(4)
If
the
pattern
in
section
0
of
the
figure
on
the
left
is
the
original
design,
press
"001"
to
program
the
pattern
in
section
0,
"011"
to
program
the
pattern
in
section
0,
and
"010"
to
program
the
pattern
in
section
O.
Operate
the
numeral
keys
to
indicate
the
appropriate
number
on
the
STEP
display.
(5)
Press
the
M
key,
and
then
press
the
g
key.
(6)
Press
the
R/W
switch
to
write
the
pattern
to
disk.
(Refer
to
page
24.)
Press
the
key
to
enter
the
sewing
mode.
Note
1
When
the
key
is
used
to
compose
a
symmetrical
mirror
image,
the
program
will
be
input
with
the
initial
stitch
position
as
the
starting
point
of
the
entire
symmetrical
pattern
as
shown
in
the
figures
below.
Note
2
In
the
event
that
the
mirror
image
may
extend
beyond
the
limits
of
the
work
clamp,
or
if
the
entire
symmetrical
pattern
is
to
be
moved
to
the
center
of
the
work
clamp,
etc.,
press
the
key
after
completing
the
procedure
from
1—5
mentioned
above.
Then,
press
the
direction
keys
to
move
the
work
clamp
to
the
newly
-established
initial
stitch
position,
and
press
the
key.
Thus,
the
newly
-established
initial
stitch
position
will
be
programmed.
(X-0,
Y-0)
O
Origin
figure
Q
"011"
-
'
L
"
1-
O
o
O
-
010
-
O
-ow
-
O
Origin
figure
0
-ow-
®0
New
position
—
Initial
stitch