Brother International BAS-300 Series Programmer Instruction Manual - English - Page 15

pattern, numeral, program, remaining, design.

Get Brother International BAS-300 Series PDF manuals and user guides View all Brother International BAS-300 Series manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

B. To program a symmetrical pattern design, the operator is only required to program one-half of the pattern and use of the numeral keys to program the remaining half of the design. Example: Program, on the Y axis, a symmetrical mirror of the pattern in the figures below. (1) Press the E] key. The work clamp will move to the point of origin (X-0; Y-0), the numeral "0" will be indicated on the display, and the command indicator "F" will illuminate. (2) Operate the direction keys to move the work clamp to the initial stitch position. (3) When the tip of the needle and the initial stitch position ® on the outline of the needle movement become aligned, press the 11) key. Thus, the initial stitch will be programmed. (4) Repeat the above procedure to program the left-side half of the stitch pattern from point 0 to point (D. g (5) Press the key at point ®. Then, operate the numeral keys to indicate "442" on the STEP display, and press the El key once again. (6) The tip of the needle will slowly move from point ® to point ®, and the right side half of the pattern design will be automatically programmed. At this time, if the presser-lifter pedal is pressed, the work clamp will be fast-forwarded. (7) When the tip of the needle becomes aligned with point ®, press the numeral key 0 3 times to indicate "111" on the STEP display. Then, press the (11 key. (8)- The work clamp will move back to the initial stitch position. (9) Press the R/W switch to write the pattern to disk. (Refer to page 24.) Press the El key to enter the sewing mode. Repeat Y-axis (442), origin point (440), and X-axis (441) to program pattern (443). (X-0, Y-0) -111- (11 • "442" "440" "441" "443"

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
B.
To
program
a
symmetrical
pattern
design,
the
operator
is
only
required
to
program
one-half
of
the
pattern
and
use
of
the
numeral
keys
to
program
the
remaining
half
of
the
design.
Example:
Program,
on
the
Y
axis,
a
symmetrical
mirror
of
the
pattern
in
the
figures
below.
(1)
Press
the
E]
key.
The
work
clamp
will
move
to
the
point
of
origin
(X-0;
Y-0),
the
numeral
"0"
will
be
indicated
on
the
display,
and
the
command
indicator
"F"
will
illuminate.
(2)
Operate
the
direction
keys
to
move
the
work
clamp
to
the
initial
stitch
position.
(3)
When
the
tip
of
the
needle
and
the
initial
stitch
position
®
on
the
outline
of
the
needle
movement
become
aligned,
press
the
11)
key.
Thus,
the
initial
stitch
will
be
programmed.
(4)
Repeat
the
above
procedure
to
program
the
left
-side
half
of
the
stitch
pattern
from
point
0
to
point
(D.
(5)
Press
the
g
key
at
point
®.
Then,
operate
the
numeral
keys
to
indicate
"442"
on
the
STEP
display,
and
press
the
El
key
once
again.
(6)
The
tip
of
the
needle
will
slowly
move
from
point
®
to
point
®,
and
the
right
side
half
of
the
pattern
design
will
be
automatically
programmed.
At
this
time,
if
the
presser
-lifter
pedal
is
pressed,
the
work
clamp
will
be
fast
-forwarded.
(7)
When
the
tip
of
the
needle
becomes
aligned
with
point
®,
press
the
numeral
key
0
3
times
to
indicate
"111"
on
the
STEP
display.
Then,
press
the
(11
key.
(8)-
The
work
clamp
will
move
back
to
the
initial
stitch
position.
(9)
Press
the
R/W
switch
to
write
the
pattern
to
disk.
(Refer
to
page
24.)
Press
the
El
key
to
enter
the
sewing
mode.
Repeat
Y-axis
(442),
origin
point
(440),
and
X-axis
(441)
to
program
pattern
(443).
(X-0,
Y-0)
-
111
-
(11
•
"442"
"440"
"441"
"443"