Brother International BAS-300 Series Programmer Instruction Manual - English - Page 32

Brother International BAS-300 Series Manual

Get Brother International BAS-300 Series PDF manuals and user guides View all Brother International BAS-300 Series manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

ri To parallel-shift a programmed stitch pattern in the X axis or Y axis A. When the initial stitch is the beginning of the sewing operation. (X-0 • Y-0) (1) Set the power source switch to the ON position. (2) Press the El key. The work clamp will move to the point of origin (X-0; Y-0), the numeral "0" will be indicated on the STEP display, and the command indicator "F" will illuminate. (3) Insert the disk containing the stitch pattern program to perform the read operation. (4) Operate the direction keys to move the tip of the needle to the newly-established starting position of the sewing operation. Then, press the 111 key. (5) Press the R/W switch to write the pattern to disk. (Refer to page 24.) (6) Press the key to enter the sewing mode. B. When the initial stitch is the shunting point of the sewing operation. (1) Set the power source switch to the ON position. \ / (2) Press the key. The work clamp will move to the point of origin (X-0; Y-0), the numeral "0" will be indicated on the STEP display, and the command indicator "F" will illuminate. (3) Insert the disk containing the stitch pattern program to perform the read operation. (4) Press the numeral key and the III key. The tip of the needle will move to point A. Y (5) Operate the direction keys to move the tip of the needle to point B. (At this time, do not press the key.r x Note When the distance from point A to point B (X 0 Y 0) exceeds 8.0 mm, press either the a key or the key, and then operate the direction keys to move the tip of the needle to point B. (6) Write down the coordinates (the X and Y values) on a piece of paper. (7) Press the I] key. The work clamp will move back to the point of origin. (8) Press the numeral key and the key. The tip of the needle will move to point C. (9) Operate the direction keys according to the value of the coordinates in the X and Y axis to move the tip of the needle to point D. Note If the distance the pattern is to be moved (the distance between A and B) is greater than 8.0 mm, press the al or key, press the feed key, and move the needle point to point D. (10) Make a mark at point D so that the tip of the needle can easily be brought to this position when the pulley is turned manually. (11) Turn the pulley manually to raise the needle to the highest position. (12) Press the E key. The work clamp will move back to the point of origin. (13) Operate the direction keys to move the tip of the needle to point D (i.e., to where the mark was made.) Then, press the [1] key. (14) Press the R/W switch to write the pattern to disk. (Refer to page 24.) (15) Press the EI key to enter the sewing mode.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
ri
To
parallel
-shift
a
programmed
stitch
pattern
in
the
X
axis
or
Y
axis
A.
When
the
initial
stitch
is
the
beginning
of
the
sewing
operation.
(1)
Set
the
power
source
switch
to
the
ON
position.
(2)
Press
the
El
key.
The
work
clamp
will
move
to
the
point
of
origin
(X-0;
Y-0),
the
numeral
"0"
will
be
indicated
on
the
STEP
display,
and
the
command
indicator
"F"
will
illuminate.
(3)
Insert
the
disk
containing
the
stitch
pattern
program
to
perform
the
read
operation.
(4)
Operate
the
direction
keys
to
move
the
tip
of
the
needle
to
the
newly
-established
starting
position
of
the
sewing
operation.
Then,
press
the
111
key.
(5)
Press
the
R/W
switch
to
write
the
pattern
to
disk.
(X-0
•
Y-0)
(Refer
to
page
24.)
(6)
Press
the
key
to
enter
the
sewing
mode.
B.
When
the
initial
stitch
is
the
shunting
point
of
the
sewing
operation.
(1)
Set
the
power
source
switch
to
the
ON
position.
(2)
Press
the
key.
The
work
clamp
will
move
to
the
point
of
origin
(X-0;
Y-0),
the
numeral
"0"
will
be
indicated
on
the
STEP
display,
and
the
command
indicator
"F"
will
illuminate.
(3)
Insert
the
disk
containing
the
stitch
pattern
program
to
perform
the
read
operation.
(4)
Press
the
numeral
key
and
the
III
key.
The
tip
of
the
needle
will
move
to
point
A.
(5)
Operate
the
direction
keys
to
move
the
tip
of
the
needle
to
point
B.
(At
this
time,
do
not
press
the
key.r
Note
When
the
distance
from
point
A
to
point
B
exceeds
8.0
mm,
press
either
the
a
key
or
the
key,
and
then
operate
the
direction
keys
to
move
the
tip
of
the
needle
to
point
B.
(6)
Write
down
the
coordinates
(the
X
and
Y
values)
on
a
piece
of
paper.
(7)
Press
the
I]
key.
The
work
clamp
will
move
back
to
the
point
of
origin.
(8)
Press
the
numeral
key
and
the
key.
The
tip
of
the
needle
will
move
to
point
C.
(9)
Operate
the
direction
keys
according
to
the
value
of
the
coordinates
in
the
X
and
Y
axis
to
move
the
tip
of
the
needle
to
point
D.
Note
If
the
distance
the
pattern
is
to
be
moved
(the
distance
between
A
and
B)
is
greater
than
8.0
mm,
press
the
a
l
or
key,
press
the
feed
key,
and
move
the
needle
point
to
point
D.
(10)
Make
a
mark
at
point
D
so
that
the
tip
of
the
needle
can
easily
be
brought
to
this
position
when
the
pulley
is
turned
manually.
(11)
Turn
the
pulley
manually
to
raise
the
needle
to
the
highest
position.
(12)
Press
the
E
key.
The
work
clamp
will
move
back
to
the
point
of
origin.
(13)
Operate
the
direction
keys
to
move
the
tip
of
the
needle
to
point
D
(i.e.,
to
where
the
mark
was
made.)
Then,
press
the
[1]
key.
(14)
Press
the
R/W
switch
to
write
the
pattern
to
disk.
(Refer
to
page
24.)
(15)
Press
the
EI
key
to
enter
the
sewing
mode.
x
\
/
Y
(X
0
Y
0)