Brother International Innov-is 1000 Operation Manual - Page 89

When sewing, be sure that the needle, does not touch the button, otherwise the, needle may bend or

Get Brother International Innov-is 1000 PDF manuals and user guides View all Brother International Innov-is 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

UTILITY STITCHES Turn the handwheel toward you g (counterclockwise) to check that the needle correctly goes into the two holes of the button. Adjust the stitch width to the distance between the button holes. When you are finished attaching the button, j slide the drop feed lever to (to the right as seen from the rear of the machine) to raise the feed dogs. Memo z The feed dog position switch is normally set to the right side. z The feed dogs come up when you start sewing again. CAUTION ● When sewing, be sure that the needle does not touch the button, otherwise the needle may bend or break. Start sewing. h Set the sewing speed controller to the left (so that the speed will be slow). ■ Attaching a shank to a button To sew the button with a shank, attach the button with space between it and the fabric, and then wind the thread by hand. This attaches the button securely. Place the button into button-sewing foot "M", a and then pull the shank lever toward you. 1 X The sewing machine automatically stops after sewing reinforcement stitches. • Do not press (Thread cutter button). Use scissors to cut the upper thread and the i bobbin thread at the beginning of the stitching. Pull the upper thread at the end of the stitching to the wrong side of the fabric, and then tie it with the bobbin thread. a Shank lever After sewing is finished, cut the upper thread b with plenty of excess, wind it around the thread between the button and the fabric, and then tie it to the upper thread at the beginning of the stitching. Tie together the ends of the bobbin thread at the end and at the beginning of the stitching at the wrong side of the fabric. Cut off any excess thread. c 88

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
88
UTILITY STITCHES
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
g
Turn the handwheel toward you
(counterclockwise) to check that the needle
correctly goes into the two holes of the button.
Adjust the stitch width to the distance between
the button holes.
CAUTION
h
Start sewing.
Set the sewing speed controller to the left (so
that the speed will be slow).
The sewing machine automatically stops
after sewing reinforcement stitches.
• Do not press
(Thread cutter button).
i
Use scissors to cut the upper thread and the
bobbin thread at the beginning of the stitching.
Pull the upper thread at the end of the stitching
to the wrong side of the fabric, and then tie it
with the bobbin thread.
j
When you are finished attaching the button,
slide the drop feed lever to
(to the right
as seen from the rear of the machine) to raise
the feed dogs.
Memo
The feed dog position switch is normally set
to the right side.
The feed dogs come up when you start
sewing again.
■
Attaching a shank to a button
To sew the button with a shank, attach the button
with space between it and the fabric, and then
wind the thread by hand. This attaches the button
securely.
a
Place the button into button-sewing foot “M”,
and then pull the shank lever toward you.
a
Shank lever
b
After sewing is finished, cut the upper thread
with plenty of excess, wind it around the
thread between the button and the fabric, and
then tie it to the upper thread at the beginning
of the stitching.
Tie together the ends of the bobbin thread at
the end and at the beginning of the stitching at
the wrong side of the fabric.
c
Cut off any excess thread.
●
When sewing, be sure that the needle
does not touch the button, otherwise the
needle may bend or break.
1