Canon Microfilm Scanner 350II MS-350II Instruction Manual. 3.01 MB - Page 56

User call errors, Scanner mode, DMP mode

Get Canon Microfilm Scanner 350II PDF manuals and user guides View all Canon Microfilm Scanner 350II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

■ MAINTENANCE AND TROUBLESHOOTING ■ User call errors Here is a list of User Call Errors. If you see a User Call Error in the Print display, look it up in the table below. Scanner mode Error Number Meaning LP The lamp installed in the scanner has burned out. Solution Replace the new lamp. (➞P.49 "Replacing the lamp") L5 The lamp unit is not correctly Check the lamp installation and make sure it locks in place. installed in the scanner. If the error occurs again, replace the halogen lamp. (➞P.49 "Replacing the lamp") DMP mode Error Number Meaning P0 After removing a piece of jammed paper, a sheet of paper is still jammed in the printer. Solution Remove the jammed sheet from the printer. For details, refer to the printer manual. P1, P2 A sheet of paper has jammed inside Remove the jammed sheet from the printer. For details, the printer. refer to the printer manual. LP The lamp installed in the scanner Replace the new lamp. (➞P.49 "Replacing the lamp") has burned out. L1 Paper is not set in the printer. Supply paper to the paper cassette of the printer. For details, refer to the printer manual. L2 Toner in the toner cartridge is low, Remove the toner cartridge and install it again. If the or the toner cartridge is not installed message appears again, replace the toner cartridge. For correctly. details, refer to the printer manual. L4 The printer cover is open. Close the printer cover and make sure it locks in place. For details, refer to the printer manual. L5 The lamp unit is not correctly Check the lamp installation and make sure it locks in place. installed in the scanner. If the error occurs again, replace the halogen lamp. (➞P.49 "Replacing the lamp") L8 Wrong paper size in printer multi- Re-load the tray with the correct paper size, or change purpose tray. the paper size of the paper tray. (➞P.43 "Printing (DMP mode)") L9 The printer is not turned on, or a test Turn on the power. Wait until the test print finishes and print is being done. then do the operation. For details, refer to the printer manual. 54 CE-IE-335-01 54 If "L1" is displayed while Fileprint 270 is printing, after the paper stops feeding press the Clear/Stop key to clear the error display and then press the Start key to start printing again. 07.5.14, 14:20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
54
■
MAINTENANCE AND TROUBLESHOOTING
■
User call errors
Here is a list of User Call Errors. If you see a User Call Error in
the Print display, look it up in the table below.
Scanner mode
Error Number
Meaning
LP
The lamp installed in the scanner
has burned out.
L5
The lamp unit is not correctly
installed in the scanner.
DMP mode
Error Number
Meaning
P0
After removing a piece of jammed
paper, a sheet of paper is still
jammed in the printer.
P1, P2
A sheet of paper has jammed inside
the printer.
LP
The lamp installed in the scanner
has burned out.
L1
Paper is not set in the printer.
L2
Toner in the toner cartridge is low,
or the toner cartridge is not installed
correctly.
L4
The printer cover is open.
L5
The lamp unit is not correctly
installed in the scanner.
L8
Wrong paper size in printer multi-
purpose tray.
L9
The printer is not turned on, or a test
print is being done.
Solution
Remove the jammed sheet from the printer. For details,
refer to the printer manual.
Remove the jammed sheet from the printer. For details,
refer to the printer manual.
Replace the new lamp. (
➞
P.49 “Replacing the lamp”)
Supply paper to the paper cassette of the printer. For
details, refer to the printer manual.
Remove the toner cartridge and install it again. If the
message appears again, replace the toner cartridge. For
details, refer to the printer manual.
Close the printer cover and make sure it locks in place.
For details, refer to the printer manual.
Check the lamp installation and make sure it locks in place.
If the error occurs again, replace the halogen lamp.
(
➞
P.49 “Replacing the lamp”)
Re-load the tray with the correct paper size, or change
the paper size of the paper tray. (
➞
P.43 “Printing (DMP
mode)”)
Turn on the power. Wait until the test print finishes and
then do the operation. For details, refer to the printer
manual.
Solution
Replace the new lamp. (
➞
P.49 “Replacing the lamp”)
Check the lamp installation and make sure it locks in place.
If the error occurs again, replace the halogen lamp.
(
➞
P.49 “Replacing the lamp”)
If “L1” is displayed while Fileprint 270 is printing, after
the paper stops feeding press the Clear/Stop key to
clear the error display and then press the Start key to
start printing again.
CE-IE-335-01
07.5.14, 14:20
54